Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 76 Highboy
#1

Back in Feb I scored a nice model 95 Highboy, see earlier post.  Saved from a guy that likes chopping them up into Liquor cabinets.  Icon_thumbdown Icon_thumbdown   Yesterday I found its brother, a model 76 Highboy.  Same cabinet, different chassis inside.  I believe there was four different radios you could get in this cabinet back in 1929.  As with the model 95, this one is in great shape original finish with a tapestry cloth in fantastic shape.  This one has a bit of veneer peal on the bottom of both sides, but not too bad and easily fixed.  Could not pass it up for only $40. Bonus, this one still had a good RCA UX245 in it.  Icon_thumbup Icon_thumbup   Issue is, I don't have room for all of these consols.  Plan to get them both running and then will have to let one go.


Attached Files Image(s)
                           

Philco's: 86 Low Boy, 90 High Boy, 95 High Boy, 76 High Boy, 112X Console, 118X Console, 41-265 Console, 41-608P Console, 52GC, 370 LZ, 512, 20 Baby Grand, 70 Baby Grand, 71B, 52B, 118B, 60B, 84B, 610B, 37-89B, 38-10T, 38-35B, 41-221CI, 42-321T, 46-1203
48-214, 48-206, 49-506
     
     
      

#2

That's a nice looking cabinet. With a little bit of rub on stain and paste wax that should even out the finish. When you replace the filter caps on this set it's important to use film cap rather than ecaps. They're low values like 1 or 2 mf @630v.  Primaries on the rf coils a lot of times are open, not a big deal to rewind. 

Have fun chasing electrons!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2315 online users. [Complete List]
» 1 Member(s) | 2314 Guest(s)
Avatar

>