Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Clear Schematic for 41-255
#16

RossH -

Were you looking at our copy of the 1941 Yearbook, or one that you found elsewhere?

Dale H. Cook, GR/HP/Tek Collector, Roanoke/Lynchburg, VA
https://plymouthcolony.net/starcity/radios/
#17

Ross, sorry, clicked on the wrong one. here's the down load for the 41-255 as an attachment.


Attached Files
.pdf Part44-Philco 1941 RMS Year Book.pdf Size: 1.35 MB  Downloads: 103
#18

What's really funny is I looked at the pages and saw 255 and it took me 30 sec of looking at the schematic trying to figure out why it wasn't matching what I had before it dawned on me - I had transposed the numbers in my head.

This is perfect. Besides starting to work on one of these I am going to recreate this schematic from scratch. I've done a few ten others but this will be my first Philco recreation. I'll post when it's completed and gone over a few times. 

Thank you very much for your time and consideration in doing this, and a big thank you to all who chimed in.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.
#19

Hello Ross,
We have all been there don't worry the guys here have you taken care of !!
Sincerely Richard
#20

Hi Ross,
I don't know if you still need a clear schematic for the 41-255 but here is one that I cleaned up. I added pin numbers on the tubes and corrected 2 part #s (#29 and 33 were reversed on the schematic). Also, voltages are in dark red, and where provided, I color-coded the wire color name.
Fran


Attached Files
.pdf Schematic-pdf.pdf Size: 1.37 MB  Downloads: 109
#21

AH Just noticed 1 error on my cleaned-up schematic...
Part # 27 - the 8uf electrolytic cap...The lead that is marked RED should read GRN (green). Old eyes are not what they used to be!
Fran
#22

Thank you, Fran. I'll add it to the mix.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 80 Antenna Issue?
Thanks Gary and Rod.  I also found an article in the Philco Repair Bench under Service Hints and Tips, about installi...Hamilton — 12:32 PM
Model 80 Antenna Issue?
Hello Hamilton, here is a little information found in our Philco Radio Library at the bottom of the Home page. Hope it ...GarySP — 11:28 AM
Model 80 Antenna Issue?
I did as you suggested and touching the middle of the volume control did nothing so the coil has to be rewound. Any idea...Hamilton — 10:19 AM
1949 Motorola 5A9M
This would be the second portable in the "other radios" forum where I have a similar one in my collection. I h...Arran — 12:41 AM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Hi PittsburgTost. The record changer looks like a Garrard or BSR (Likely Garrard). The spindles just pull out and pu...MrFixr55 — 11:57 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Hello PittsburghToast , Welcome aboard and it looks like gary may have something for you ! now if I dig through my se...radiorich — 11:35 PM
Model 80 Antenna Issue?
You are kind of on the right path. You can touch the grid cap of the Detector/Oscillator 36 tube. I'm expecting a respon...RodB — 08:48 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Welcome to the Phorum, PittsburghToast!  I found an old thread that my interest you regarding the quality and worth of P...GarySP — 08:48 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Welcome to the Phorum! :wave: We do not have anything on that unit in our digital library. There is a Sam's Photof...klondike98 — 08:47 PM
Model 80 Antenna Issue?
I’ve replaced all the caps and resistors and the radio is working but minimal volume unless I put my hand near the re...Hamilton — 08:24 PM

[-]
Who's Online
There are currently no members online.

>