Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA WV-98c
#16

Two things.

1. Make sure your switch is clean and provide good contact across all ranges. It is S2 Range switch.
2. I don't think this is it (I think only the lower dual triode is involved for DC, as for everything else), but just in case, have the tubes been checked?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#17

Tubes and resistors are fine. R22 measures 9k so iam not sure if that could be the issue.
#18

Switch. Check the switch. Make sure it makes good contacts. Clean if necessary, Deoxit D or any contact cleaner (be careful and don't spray it all around).

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#19

I cleaned and checked the sw2 switch, its fine. Has to be something in the .5v to 15v circuit. Iam going to check the ac operation.
#20

No ac function. Pegs the meter to the left, no adjustment.
#21

If I had it in front of me, I would triy to trace the signal on one of the non-working functions.
Try to trace and highlite at least one non-working path.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#22

At this point, there is no input, just internal voltages
Which are incorrect and not sure what they should be.
#23

Those will probably depend on teh switch combination.

Could you list some that you see, their values and what they should be (if you know correct values)?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#24

Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative voltage on it.
https://www.dropbox.com/scl/fi/gnvltn9la...fvikk&dl=0
#25

If this is R22, check the voltage on the wiper (86V).
If this is R33, see if the lower pin indeed connected to GND, the wiper is indeed wipes, and if the pot is OK.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#26

I measured the wiper of r22 , 95vdc.
#27

The resistor you are touching at the video, is it R22 or R33?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#28

R22, but it doesnt do that all the time. Strange. What do you think of the 95 voltage. I guess its close.
#29

Yes, it is close. It is a solid state diode rectifier, so the voltage won't depend much on the load, as would with tube rectifier.
However the behavior is strange.
Also, see if this pot,s case (and so the shaft) should be grounded through the fron panel, and somehow it is not.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#30

Case and shaft go to case. Center wiper of r22 has 3kohms to case.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 16B Parts
I think the chassis is painted.morzh — 08:13 PM
Philco 38-2 Automatic Tuning
Honestrly, the original is quite acceptable and, it seems to me, can be cleaned.morzh — 08:11 PM
Philco 41-608 changer coupler
Mondial left a thread about remanufacturing thois type coupler.morzh — 08:09 PM
IF can wire size and Rubber mounts?
Are you talking about rewinding or rewiring? For rewiring, meaning runnin wires to the coil from other components, the ...morzh — 08:08 PM
12' Philco
I wonder who would be able to "no stoop" with this one.morzh — 08:05 PM
IF can wire size and Rubber mounts?
Hello PHORUM members, I am still working on restoration of my PHILCO 37-640.  I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM
Philco 41-608 changer coupler
I am working on a Philco 41-608 with the gear-driven changer.  The coupling (#35-2220) between the motor assembly and th...alangard — 06:29 PM
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM

[-]
Who's Online
There are currently 3767 online users. [Complete List]
» 2 Member(s) | 3765 Guest(s)
AvatarAvatar

>