Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Two things.
1. Make sure your switch is clean and provide good contact across all ranges. It is S2 Range switch.
2. I don't think this is it (I think only the lower dual triode is involved for DC, as for everything else), but just in case, have the tubes been checked?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
Tubes and resistors are fine. R22 measures 9k so iam not sure if that could be the issue.
Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Switch. Check the switch. Make sure it makes good contacts. Clean if necessary, Deoxit D or any contact cleaner (be careful and don't spray it all around).
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
I cleaned and checked the sw2 switch, its fine. Has to be something in the .5v to 15v circuit. Iam going to check the ac operation.
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
No ac function. Pegs the meter to the left, no adjustment.
Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
If I had it in front of me, I would triy to trace the signal on one of the non-working functions.
Try to trace and highlite at least one non-working path.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
At this point, there is no input, just internal voltages
Which are incorrect and not sure what they should be.
Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Those will probably depend on teh switch combination.
Could you list some that you see, their values and what they should be (if you know correct values)?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative voltage on it.
https://www.dropbox.com/scl/fi/gnvltn9la...fvikk&dl=0
Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
If this is R22, check the voltage on the wiper (86V).
If this is R33, see if the lower pin indeed connected to GND, the wiper is indeed wipes, and if the pot is OK.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 11-10-2024, 03:29 PM by morzh.)
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
I measured the wiper of r22 , 95vdc.
(This post was last modified: 11-10-2024, 05:14 PM by daveone23.)
Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
The resistor you are touching at the video, is it R22 or R33?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
R22, but it doesnt do that all the time. Strange. What do you think of the 95 voltage. I guess its close.
Posts: 15,816
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Yes, it is close. It is a solid state diode rectifier, so the voltage won't depend much on the load, as would with tube rectifier.
However the behavior is strange.
Also, see if this pot,s case (and so the shaft) should be grounded through the fron panel, and somehow it is not.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 11-10-2024, 07:20 PM by morzh.)
Posts: 95
Threads: 19
Joined: Jun 2024
City: tampa
State, Province, Country: florida
Case and shaft go to case. Center wiper of r22 has 3kohms to case.
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Hickok AC51 tube tester
|
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM |
Philco 42-1008 conversion kit
|
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM |
HiFi (Chifi) tube amp build - but my own design.
|
Tim
Well...a chassis is metal. Magnetic or not, it does not matter.
A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM |
Hickok AC51 tube tester
|
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM |
Shadow Meter Bulb
|
Ross
I am not sure what current limiting effect the incandescent provides.
They are two different parts of the sch...morzh — 08:31 PM |
12' Philco
|
Bob
Thanks for that photo.
I have been looking for it, and I cannot find anythinmg on the web.
I forgot it was here...morzh — 08:29 PM |
Shadow Meter Bulb
|
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55.
I ...georgetownjohn — 07:31 PM |
12' Philco
|
There was also this Philco!
klondike98 — 07:25 PM |
HiFi (Chifi) tube amp build - but my own design.
|
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM |
Shadow Meter Bulb
|
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM |
Who's Online
|
There are currently no members online. |
|
|