Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-2 Low Volume
#46

It has but not RF as I don't have the dial yet.
#47

RF does not matter: IF does. This RF transformer is RF; if not aligned, it will attenuate the signal.
Make sure it is peaked, both sections.
And, then try to remove the tube 6H6 and see if it affects the loudness in the tracer.
You could also try to increase C45 to 1uF, see if it makes things better. The time constant of this filter is in audio frequency. Not sure why.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#48

Using the tracer, when I pull the 6H6 it gets a little louder on the 6R7. Didn't seem to change at all on the 6K7 tube.
#49

Did you have a cap in series with the signal tracer probe? Is there a diode in series with the probe? If yes to both then you may have to turn down the gain of the tracer. If no cap, then you may have been overdriving the tracer with B+

Ohm the secondary. It should be quite low, about 8 Ohm. There is a good possibility that it is open. If you connect the tracer to either diode plate of the detector / 1st AF Amp Tube (6R7), i suspect that the sound level will be low. Isolating the ground on the probe with a large cap (like 0.1uF, connect ground side of the probe to the green wire on the IF Out trans and probe the brown wire with a diode in the circuit. The signal should be quite loud.

Note that there are 2 100pF caps, 39A and 39B, each between ground and either side of R43. These are likely mica and, although rare for them to fail, it may still be possible. Excessive leakage of either cap will definitely lower the volume and AVC signal.

Hope this helps.

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards, 

MrFixr55
#50

C45 serves as a decoupling cap for the B+ for the IF Stage. If all components test good, revisit the IF and Local Osc alignment. Remember that the oscillator must be 470KHz above the desired station. If this cannot be adjusted to be within spec, you may have to align the IF not to 470 KHz but to the difference that you actually get between the local oscillator frequency and the station frequency.

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards, 

MrFixr55
#51

MrFixr55 I am using the second schematic, the one with the X parts as that is my radio. The 39A and B are 16X, containing 110pf caps that are in a bakelite block. I had already changed them with silver micas. Having to use two different schematics sure makes this harder. Some sections are on one and some the other.

The coils in both IFs are all good. I had checked them a while ago.

No caps in series with probes. I will try again with caps. I was told a while ago there were blocking caps in the tracer. Not sure about the ground though.

I don't know how to measure the difference frequency. I don't have a scope so the best I might do is a frequency counter but I would not know how to do that either.

As for the non peaking compensator I'm wondering if the internal cap might be bad. The schematic does not list the value for them except for 2XD (110pf) which I changed.

If RF alignment is off could that render the AVC inactive? I'm wondering if I should put the radio aside until I get my dial and then I can do the RF alignment.
#52

BTW, when you do all that, is your magnetic tuning ON or OFF?
Should be OFF.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Hello Tim, It looks very nice so far ! Sincerely Richardradiorich — 10:55 PM
HiFi (Chifi) tube amp build - but my own design.
It's getting along!morzh — 10:54 PM
HiFi (Chifi) tube amp build - but my own design.
Construction has started! So far, I've gotten the power supply done and filament wiring run. The major layout is finishe...TV MAN — 10:42 PM
RCA WV-98c
Just occurred to me: what if you have a power transformer leak? From a, say, secondary to the case. If it is bolted to t...morzh — 10:24 PM
[split] Newbie questions RE: Philco 41-608
Honestly, I do not see any capacitors, but as long as you know now, what the wiper is, this is all that matters.morzh — 10:17 PM
[split] Newbie questions RE: Philco 41-608
Morzh I changed the capacitor at the volume control as part of the full recap.  Just to confirm the 3rd pin "wip...tmurphy — 09:47 PM
Model 96 cabinet veneer
I thought it looks most like the quarter sawn flexible veneer that Constantine's sells, but I wanted another opinion.  T...TGLager — 09:19 PM
[split] Newbie questions RE: Philco 41-608
MrFixr55 The cap to the left is 21B.  I have the negative tied to the ground with two terminal points.  (See first pic ...tmurphy — 08:59 PM
Philco 39-116 radio and remote
With regard to the 39-116, (at least the U.S versions) I believe that they used rubber/gutta percha wire for the leads, ...Arran — 08:37 PM
Testing a power transformer
Well, this is where you might use that dim bulb. And, as for "can't afford", A $50 one? If you cannot...morzh — 08:28 PM

[-]
Who's Online
There are currently no members online.

>