Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
After having attached the line cord, I checked the switch and the volume pot again. That is, I did check the switch before. Intermittent. But it's the pot that is bad. Even after restoring the wiper to rheostat contact with Fafer lube, the rheostat itself is over 3M at the nominal of 350K.
I think, a call to Mark Oppat is going to happen.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 4,747
Threads: 52
Joined: Sep 2008
City: Sandwick, BC, CA
Mike;
So if you check the resistance from end to end the volume pot reads 3 meg Ohm? I could see 1 meg maybe, if someone had changed the control, but something weird is going on, it would be more normal for the resistive element to wear out, which would men that the wiper would not make contact. If it were my set I would investigate, but then again I've had to clean out a lot of controls in farm battery radios so I'm not too concerned about breaking something.
Happy Christmas
Arran
Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
Arran
The control is original. The wiper is some sort of round brass plate, that probably just digs into the carbon every time it's turned. And, yes, end-to-end is between 2M and 3M. Right at the leads. I will have to check the wiper contact again after yesterday's F5 bath dries up  but this is not expected to change the rheostat's value.
I will see if I have a stash of suitable values parts; likelyh not; the values would be from 250K to 500K or so.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
After having ordered the pot from eBay (cheap enough, $10 or so and free shipping) I realized I have a small box in my organizer labelled "potentiometers" where I found 3 pots, two of which fit the application, and one of which was fully functional.
The "D" on the shaft is a bit deeper so will have to be padded when the knob is installed. The ground was provided separately (on 60s the lower lead is grounded to the case and the chassis).
I gave it a profilactic F5 injection.
Now I am almost ready to power up. After inspecting the coils.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 12-27-2024, 12:35 PM by morzh.)
Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
Remembered that I wanted to clean the tuning cap.
At the same time the rust spots are better accessible without the cap in.
Washed it in hot soapy water.
Before
After
When I blew some air at it, small mica flakes started coming out. Never had mica disintegrating before. Guess I buy some mica sheets and replace it, if needed.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 142
Threads: 11
Joined: Jan 2024
City: Tulsa
State, Province, Country: Oklahoma
I was unaware that these air tuning capacitors contained any mica. Are the individual stator and rotor plates coated in mica?
Joseph
Philco 46-480
Philco 49-906
Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
No. The padders on the side, small caps in parallel to each section, contain mica.
Those two brass screw/nuts on the side.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 12-27-2024, 11:38 PM by morzh.)
Posts: 142
Threads: 11
Joined: Jan 2024
City: Tulsa
State, Province, Country: Oklahoma
The trimmer caps, that’s right. Somehow I didn’t consider those.
Joseph
Philco 46-480
Philco 49-906
Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
Yep. I ordered some mica pieces for TO-type transistor heatsink mounts; should come tomorrow. Not expensive and will likely last me 'till my demise, whether it will take 20 years or 1 year.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 142
Threads: 11
Joined: Jan 2024
City: Tulsa
State, Province, Country: Oklahoma
Let’s hope for 20. We need your expertise! Surely your family hopes for 20 as well.
Joseph
Philco 46-480
Philco 49-906
Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
I hope that they hope 
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,994
Threads: 558
Joined: Oct 2011
City: Jackson, NJ
Reassembled the tuning cap, it works fine, the gear works fine, and the padders also work fine. No short, nice capacitance change, so I think I will use it the way it is now.
I received a volume pot, but will stash it for the future projects, and also the mica sheets will be reserved for those just in case situations.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
1930s Stewart-Warner Tombstone Radio need help identifying model number
|
| OK, so I have run into a little issue with my radio, I put the radio back together and turned it on and I can't get the ...captainclock1988 — 01:42 AM |
|
the worlds largest CRT Television,, not philco - KX45ED1
|
| you will have to do the REDDIT leg work but..............
if you watch the vid you will see the channel or sub channel o...jcassity — 09:07 PM |
|
Philco 49-607 inop
|
| Well, why don't you simply put your ohmmeter across the switch ans this will be your answer?morzh — 05:22 PM |
|
Philco 42-390 voltage drop
|
| You need to tell us more.
Everytrhing you've done up to this point, what's connected, what's not, etc.
Have you done...morzh — 05:21 PM |
|
Philco 60 restoration
|
| Reassembled the tuning cap, it works fine, the gear works fine, and the padders also work fine. No short, nice capacitan...morzh — 05:18 PM |
|
Philco 49-607 inop
|
| I did not read continuity across any of the 3 connections on the power switch when I turned the radio on. Does that mean...Tennangler — 04:49 PM |
|
Philco 42-390 voltage drop
|
| Hello everyone just started a new project 42-390. I replaced the 2 capacitors (89) and (49) my voltage coming off 6x5 tu...winamp920@yahoo.com — 03:20 PM |
|
the worlds largest CRT Television,, not philco - KX45ED1
|
| And to think I threw away my 27" CRT 15 years ago. I left the monster on the curb. No one took it even though it wa...Kestas — 03:07 PM |
|
Philco 49-607 inop
|
| The filaments are a string, so you need to check everything that is a part of that string. Any tube with bad filament, b...morzh — 01:50 PM |
|
Philco 60 restoration
|
| I hope that they hope :lol:morzh — 01:47 PM |
|
Who's Online
|
There are currently 1785 online users. [Complete List]
» 2 Member(s) | 1783 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
