1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
cap question
ipwizard
Senior Member
****
Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek State, Province, Country: Ohio
#1

10-06-2011, 12:33 AM
I want to restuff a metal cap (non elec) it is a .50uf. The only cap I have close is a fat .47uf which will not fit inside the metal housing. Could I use two 1.0uf caps in series, or 2 .44uf caps in parallel? Im not sure what that does to the voltage value. The 1.0uf caps are only 400v, and the .22uf caps are 630v.
-Keith
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#2

10-06-2011, 12:58 AM
Two 1mFd caps in series would be 0.5 mfd, if it would fit....

Seems like I saw 0.5mFd electrolytics somewhere, they should be small enough to work in the can....
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#3

10-06-2011, 01:03 AM
Here is a link to a site that sells .47mFd electrolytics, but they are radial lead, not axial.

http://www.sterenshopusa.com/catalog/sea...CAPACITORS
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#4

10-06-2011, 01:54 AM
Two .22 caps would be fine. Still 630V.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
ipwizard
Senior Member
****
Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek State, Province, Country: Ohio
#5

10-06-2011, 11:20 AM
Sorry I wasn't clear the cap I'm trying to restuff is non-electrolytic. If I could parallel two .22 caps and get .44 and keep the voltage at 630V i'll go that route. Should be close enough to .50uf to work right?
-Keith
Find
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#6

10-06-2011, 12:37 PM
Yes, that will work just fine.
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 6446 online users. [Complete List]
» 3 Member(s) | 6443 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration