1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 610B Tone Control 30-4318 caps
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#1

10-12-2011, 11:26 AM
Hi all, Have some conflicting info on the cap values for this tone control. Both my Philco schematics(one early and one later production) list .01 and .02. I have Ray's original "Philco Condensers and More" ( Great resource book!!!) which lists a .02 and a .003 for this tone control. The Philco Repair Bench does not list this tone control. Does anyone know which would be the correct ones? I'm assuming the .02 value is correct. Thanks-Ken
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#2

10-12-2011, 02:37 PM
Those caps aren't that critical, either combination will work. Use what you have, just follow correct layout (placement). Yes, the Philco Condensers and More book is nice to have!! Best of luck with your restoration.
Find
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#3

10-12-2011, 02:56 PM
Thanks for the input. Will probably go with whats listed in the Philco schematic-Ken
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#4

10-12-2011, 09:01 PM
Go with to .003 and .02. That will give you a fair amount of difference between the two setting.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#5

10-12-2011, 11:01 PM
Yes, agree with Terry, .003 and .02 are a good combination for steps in tone.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Hi OSanders. another thing about the loop antenna is that it is directional. Try turning the radio in different direct...MrFixr55 — 09:19 PM
Philco 42-345 Restoration/Repair
The 630v caps will do just fine. Physical size increases with capacity values and voltage. You don't have to replace 200...RodB — 09:09 PM
Help with Supreme 599
Good catch. The 589 is a better schematic but i dont understand how the voltage goes thru the meter to adj the line volt...daveone23 — 08:17 PM
1949 Motorola 5A9M
Arron, Yes, I can see the differences in the interior design, but if you compare the schematics, they look very similar...Vlad95 — 06:57 PM
Philco 42-345 Restoration/Repair
I am not sure how the loop antenna supposed to work but think I have figured it out. I had one lead on terminal 1 and go...osanders0311 — 06:56 PM
1949 Motorola 5A9M
Thx Vlad.klondike98 — 06:54 PM
Rogers Majestic R-646
Hi Arran. I continue to disassemble and I see that the interstage transformer is completely beyond repair. It is placed...Vlad95 — 06:50 PM
Philco 42-345 Restoration/Repair
Hello Rod " If you're not using the 0.33 mfd 200 volt ones for this project, they are excellent tweeter crossover ...osanders0311 — 06:25 PM
Rogers Majestic R-646
Vlad; My set had the same faults as yours when it was about 30 years younger, so I think that these components are sus...Arran — 05:11 PM
Philco 42-345 Restoration/Repair
If you're not using the 0.33 mfd 200 volt ones for this project, they are excellent tweeter crossover caps.RodB — 04:56 PM

[-]
Who's Online
There are currently 423 online users. [Complete List]
» 1 Member(s) | 422 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration