Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

volume control
#1

Can someone tell me the resistance of a philco 7439 volume control.
#2

If it is for the model 80 it's 20K. Two quick checks, one unplug set turn volume all the way up. Measure resistance from ANT post to chassis ground. Should be very low like a few ohms. If not antenna coil primary is open. Two, Turn volume all the away down.Measure resistance from antenna post to chassis ground. Should read about 20,000 ohms. If not check volume control, open or bad ground connection.
How's your oscillator doing?
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

What model Philco are you working on?

I didn't see any data on your part number on Philcorepairbench.com.

-Keith
#4

Terry is correct, it is 20K. Part no. 7439 was used in model 80 and the three-knob 81.

--
Ron Ramirez
Ferdinand IN
#5

Do I get a prize????
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Yeah - a Philco 84B that needs complete restoration. Icon_twisted Icon_lol

--
Ron Ramirez
Ferdinand IN
#7

I unsoldered one outer lug, not the one to ground and measured it like a resistor, 17 ohms.
Strange, then I unsoldered the center lug and it read 27k. I thought you can measure a pot like a resistor if one of the outer lugs is disconnected.
#8

Depending on the circuit this may not be true, IE this case. However if the wiper is all the way toward the still connected end you should be able to get an accurate reading. Then you could connect the ohmmeter between the center and unconnected end and sweep it, and you will then see if there are any open spots.
#9

It also maybe effected by the very low resistance of the antenna coil connected to the wiper and ground.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco Model 95 High Boy
So today I get published as I update my collection in the Radio Museum web site. I tried to published pictures of my Phi...slford310 — 08:00 PM
Philco 84 antenna connection
Very simply connect al long piece of wire to that contact for your antenna.   A piece 10 to plus 50 feet is no issue dep...slford310 — 07:46 PM
Philco 46-480 Cabinet Restoration
I like it!Burchjburch — 05:57 PM
Philco 46-480 Cabinet Restoration
I knew when I asked the question here, that I just wasn’t satisfied with the darkness of the stain. Today I took some mi...jrblasde — 04:54 PM
Philco 84 antenna connection
I've used a single long wire up as high as possible and away obstacles. The gnd can be connected to a copper water pipe ...Radioroslyn — 03:34 PM
Philco 51-632
Found this today for $10 in the local resale shop. It’s a violation of good procedure but I put it on the variac. It cam...bridkarl — 03:25 PM
Philco 41-221 Restored
Rod Great job, looks good, no need to refinish to my taste. It is rare that you see the tenite grill in these in decent...morzh — 03:01 PM
My last cabinet for this year
Beautiful Job!!!! Looks awsomeslford310 — 03:01 PM
Identify Philco Radio
Thank you Terry.dconant — 02:41 PM
Philco 84 antenna connection
Hello Everyone, I was wondering what was the best way to connect an antenna for testing on my Philco 84. The field co...Ctkid — 01:38 PM

[-]
Who's Online
There are currently 3474 online users. [Complete List]
» 2 Member(s) | 3472 Guest(s)
AvatarAvatar

>