Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grandfather clock radio, Model 70
#1

I just got a Grandfather Clock Radio, it has a Philco Radio Model 70 Superheterodyne radio, with a Hammon clock. It has a paper label with says it was made by The Dearborn Co, Chicago, IL. Can any one give me more info on this radio or point me in the right direction. The clock works fine, so far I know I need to replace the cord on the radio. I would like to restore this right not half way. It is a nice clock/Radio. I am new to radios because I've always collected clocks, looks like I may be getting into radios somewhat. I've added a photo, any help would be great.

Note from site admin: Sorry, but the photo which was attached to this post is no longer available.
#2

Hi Herb
Welcome to the phourm!
Model 70(chassis) is a fairly common model but there are two different versions of it. There was an early and late version and electrically are very different from each other.
Probably the easiest thing for starters is to do a search in the phourm on Model 70.
I've got the model 370 which is the model 70 in a chairside cabinet. The 70 in a clock cabinet is known as a 570
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7744 online users. [Complete List]
» 2 Member(s) | 7742 Guest(s)
AvatarAvatar

>