1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
42-1008 speaker/turn table question
Guest
Unregistered
 
#1

11-22-2006, 10:17 PM
I would like to replace the speaker with something new. What should I choose? I am also thinking of removing the turn table and installing a modern one - should I? If not, where can I find a new needle?
Guest
Unregistered
 
#2

11-22-2006, 10:32 PM
How about the Cerwin Vega 12" dual-voice?
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#3

11-23-2006, 11:06 AM
A modern 12-inch PM speaker will NOT work in this set without some power supply modifications. The original speaker (part no. 36-1528 ) is an electrodynamic type and the filed coil is also the filter choke in the power supply. The field coil D.C. resistance is 1,000 ohms and the voice coil impedance is 5.1 ohms.

Try Play Things of Past (http://www.oldradioparts.com) for a possible replacement speaker or a junker set on ebay. Same speaker is also used in the 42-1009. A compatible speaker (part no. 36-15224 or 36-1565) was also used in Models 42-1012, 1013, but with a slightly lower field coil resistance of 860 ohms. A suitable power resistor could be added in series with it to compensate.
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 6330 online users. [Complete List]
» 2 Member(s) | 6328 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration