Posts: 44
Threads: 9
Joined: Apr 2011
City: Pittsburgh, PA
Still new at this and new to Philco and superhets. Is it necessary to pull the coils out to test them? I haven't found a definitive answer in my research. Is there a cheat sheat available showing point to point testing that would verify continuity in all the coils w/o disturbing them. Thanks in advance. One curious thing I found was a single 16 mfd ecap instead of the 2 8mfds...probably a repair??? No stations as yet and I replaced the 16 mfd with a 22 mfd.
Posts: 7,283
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Most of the time the primary of the antenna coil and the feedback winding of the oscillator coil are the one that are commonly open.
Terry
(This post was last modified: 02-27-2012, 08:57 PM by Radioroslyn.)
Posts: 44
Threads: 9
Joined: Apr 2011
City: Pittsburgh, PA
(02-27-2012, 08:56 PM)7estatdef Wrote: Most of the time the primary of the antenna coil and the feedback winding of the oscillator coil are the one that are commonly open.
Terry
The only sound I get is steady soft hum and a noise like somebody is hitting radio with a rope at a steady cadence...curious.
Posts: 7,283
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Go a head and replace the paper caps, electrolytic caps and out of spec resistors. Then we can talk about coils.
Terry
Posts: 44
Threads: 9
Joined: Apr 2011
City: Pittsburgh, PA
After recapping the bakelites and rewinding the primary of the osc coil...still nothing in terms of reception. Primary of osc coil now measures 2.1 ohms vs. 3.4 of schematic. Antenna on grid cap of 6A7...still nothing. The .7 SW of antenna coil measures open. Would that knock out even BC reception??
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
(03-19-2012, 08:39 AM)sjhs1962 Wrote: After recapping the bakelites and rewinding the primary of the osc coil...still nothing in terms of reception. Primary of osc coil now measures 2.1 ohms vs. 3.4 of schematic. Antenna on grid cap of 6A7...still nothing. The .7 SW of antenna coil measures open. Would that knock out even BC reception??
It is customary to post link to schematic with question
http://www.nostalgiaair.org/PagesByModel...013793.pdf
If the antenna coil is open, it needs to be rewound or replaced. That being said and if voltages are reasonable, work backwards from the speaker (right to left) with a modulated signal generator to find out where you are losing signal.
Posts: 7,283
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
If the primary of the ant coil as open you can hook the ant to the grid cap of the mixer tube and you should be able to receive radio signals. Is you local oscillator working?
Terry
Posts: 44
Threads: 9
Joined: Apr 2011
City: Pittsburgh, PA
(03-19-2012, 04:33 PM)7estatdef Wrote: If the primary of the ant coil as open you can hook the ant to the grid cap of the mixer tube and you should be able to receive radio signals. Is you local oscillator working?
Terry
http://www.philcoradio.com/tech/60evol.htm
No, oscillator not working. In addition plate voltages are high 370 vdc. Also, resistor on band switch measures 11 ohms ...schematic says 10k, but I have another 60 in a different version that works and this resistor also measures 11 ohms. Confused. Antenna on grid cap of 6A7 doesn't bring in anything.
(This post was last modified: 03-19-2012, 08:52 PM by sjhs1962.)
Posts: 15,704
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
Your resistor measures 11 Ohm because it is in parallel to the antenna coil that actually says "11 Ohm" on it.
You know how paralleling resistors work, right?
(This post was last modified: 03-19-2012, 09:15 PM by morzh.)
Posts: 44
Threads: 9
Joined: Apr 2011
City: Pittsburgh, PA
(03-19-2012, 09:14 PM)morzh Wrote: Your resistor measures 11 Ohm because it is in parallel to the antenna coil that actually says "11 Ohm" on it.
You know how paralleling resistors work, right?
Thanks...tricky concept that could trip you up easily. I found the calculator online...of course you have to know that the resistors are in parallel.
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
(03-19-2012, 09:44 PM)sjhs1962 Wrote: ...of course you have to know that the resistors are in parallel.
That's where experience in reading and interpreting a schematic helps with these kinds of issues.
Continued good luck,
Chuck
Posts: 7,283
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Well The thing isn't gonna work if the oscillator isn't running. Check the voltage on grid 2 of the 6A7. Should be pretty high like 100 volts. If not rewind oscillator feedback winding.
Terry
(This post was last modified: 03-21-2012, 06:21 PM by Radioroslyn.)
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
And make sure that oscillator feedback winding is wound counterclockwise!
--
Ron Ramirez
Ferdinand IN
Posts: 44
Threads: 9
Joined: Apr 2011
City: Pittsburgh, PA
Osc coil wire that doesn't go to any terminals on actual osc coi....what is purpose of this coil wire? Does it go to cathode of 6A7?
Posts: 44
Threads: 9
Joined: Apr 2011
City: Pittsburgh, PA
On the antena coil, the primary is the inserted coil inside the tube and the secondary has the three taps. I am wondering if it is necessary to rewind the .7 sw coil since it doesn't function for the most part?
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 91 Speaker Replacement
|
| The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM |
|
Restoring Philco 37-604C
|
| Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one.
Which does not m...morzh — 01:44 PM |
|
Philco 38-2 Automatic Tuning
|
| When you push the lever, you are supposed to rotate the disk to the desired station.
Then the magnetic tuning will acqu...morzh — 01:42 PM |
|
Philco 38-2 Automatic Tuning
|
| I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM |
|
Philco 91 Speaker Replacement
|
| How would I go about removing the spider from the cone?dconant — 12:04 PM |
|
Philco 38-2 Automatic Tuning
|
| Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM |
|
Does anyone make photofinish replacements?
|
| Here’s the link to the DIY photofinish section of our site:
klondike98 — 09:46 AM |
|
Delco car radio Peko vibrator converstion issues
|
| Hi Richard,
Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM |
|
Delco car radio Peko vibrator converstion issues
|
| hello mr Fixr,
The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM |
|
Delco car radio Peko vibrator converstion issues
|
| How about putting a choke in the power supply?
The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM |
|
Who's Online
|
There are currently 2909 online users. [Complete List]
» 1 Member(s) | 2908 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
