Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-145 speaker hole
#1

Just got this one in the mail and was wondering how do I fix about a quarter size piece of speaker cone that is missing? Other than that the radio looks good. I just started the recap on it.

What is the best material to try and patch it and what is the best kind of glue or cement? How difficult is this to do?

thanks
Chris
#2

It's an easy repair. I harvest a patch from an unused tea bag. Make sure it's large enough to cover the hole plus at least 1/2" all the way around. GENTLY spread some flexible fabric glue around the hole, apply the patch & gently brush more glue over the patch. If you can get to the back side of the cone, repeat the process on the back. Be very careful, the old paper on speakers can be extremely delicate & can tear easily, especially when wet with glue.
#3

Dave,
Thanks for the tip. never thought of using a tea bag! Will give it a try.

Chris
#4

I always used something like a good quality of bond paper to patch holes in speakers, a tea bag may be good to re-enforce a tear after gluing but it's pretty thin to cover a hole. Also remember, do not use silicone inspite of what you may have heard, silicone is for the bathtub not speaker repair.
Regards
Arran
#5

Over the years I've seen a lot different things used. Mostly bad stuff! Duck tape, news paper and white glue, masking tape, and Scotch #33 tape (black electrical tape) One guy insisted on using RTV silicone. If I sat down a thought for a few hours I couldn't think of much worst to use. I was more of a rubber cement kind of a guy but with these new glues and such it opens the doors for much better repairs
Terry
#6

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.
#7

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 16 wiring question
Well, finding a short is easy. Like I said, disconnect the transformer's secondary windings and see if it persists. If...morzh — 09:48 PM
Restoring Philco 96
Nice one!Stan the Man — 09:37 PM
Restoring Philco 96
I have eventually replaced the speaker and shot the video, which only shows the upper part of the dial as the hum is ver...morzh — 09:24 PM
Rogers Majestic R-646
Kinda weird to see both open Nothing weird if you remember that this radio is about 100 years old  :)Vlad95 — 07:49 PM
Philco 42-345 Restoration/Repair
I believe I'm making progress, resistors have been rechecked and corrected, removed that ugly blue capacitor and more wi...osanders0311 — 07:38 PM
Philco Model 16 wiring question
Thanks Morzh Yes I recapped everything and replaced almost all the resistors as well. I redid #99 with .015 safety ca...bobclausen — 07:11 PM
Philco Model 16 wiring question
Well...pull out every single load of the transformer. For every winding. Unsolder if needed. Then re-do your dim bulb....morzh — 07:02 PM
Rogers Majestic R-646
Kinda weird to see both open, but once you get it up and running, really pay attention to your sound. Listen for loud cr...TV MAN — 06:59 PM
Rogers Majestic R-646
Vlad; I was just reminded of something else, I'm not sure why but many Rogers built sets do seem to have open primari...Arran — 04:40 PM
Rogers Majestic R-646
Thanks RpdB I don't think there's much difference with interstage transformers of different models other than dimersion...Vlad95 — 03:27 PM

[-]
Who's Online
There are currently no members online.

>