Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-145 speaker hole
#1

Just got this one in the mail and was wondering how do I fix about a quarter size piece of speaker cone that is missing? Other than that the radio looks good. I just started the recap on it.

What is the best material to try and patch it and what is the best kind of glue or cement? How difficult is this to do?

thanks
Chris
#2

It's an easy repair. I harvest a patch from an unused tea bag. Make sure it's large enough to cover the hole plus at least 1/2" all the way around. GENTLY spread some flexible fabric glue around the hole, apply the patch & gently brush more glue over the patch. If you can get to the back side of the cone, repeat the process on the back. Be very careful, the old paper on speakers can be extremely delicate & can tear easily, especially when wet with glue.
#3

Dave,
Thanks for the tip. never thought of using a tea bag! Will give it a try.

Chris
#4

I always used something like a good quality of bond paper to patch holes in speakers, a tea bag may be good to re-enforce a tear after gluing but it's pretty thin to cover a hole. Also remember, do not use silicone inspite of what you may have heard, silicone is for the bathtub not speaker repair.
Regards
Arran
#5

Over the years I've seen a lot different things used. Mostly bad stuff! Duck tape, news paper and white glue, masking tape, and Scotch #33 tape (black electrical tape) One guy insisted on using RTV silicone. If I sat down a thought for a few hours I couldn't think of much worst to use. I was more of a rubber cement kind of a guy but with these new glues and such it opens the doors for much better repairs
Terry
#6

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.
#7

Best is a little left over from the last time you bought a surround kit and didn't use it all up. I think it's similar to fabric glue, but I'm not a chemist. Reckon Somewhere between Elmer's and Rubber Cement.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3962 online users. [Complete List]
» 1 Member(s) | 3961 Guest(s)
Avatar

>