Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Hello all,
Thought since the first 66 went so well,I'd try another one with all I learned. Radio works -- all caps replaced, out of specs resistors changed.
Two minor problems- tone control goes into a high pitched squeal when put in left hand position (less bass). Tone control was rebuilt. The volume control is very touchy- I cleaned it well but get very irregular control. I actually had this out of the radio and separated the on/off section and cleaned internal controls very well- they seemed to move as expected.
Any thoughts on either problem?
http://www.nostalgiaair.org/PagesByModel...013827.pdf
These problems are hopefully minor compared to the last one.
Thanks,
Joe
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
Joe, are all the tube sheilds in place and grounded to their brackets? Also make sure the grid wire to the type 75 tube is routed inside the tube sheild.
Steve
M R Radios C M Tubes
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
After following Steve's suggestions I would change the .002 in the tone control to .005 or so. That should take care of the squeal problem. It's sounds like the volume control is bad I'd replace it.
Terry
Posts: 15,819
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Here's something I don't understand. I fully expected a capacitor after the field coil to the Chassis. There is none. There should be....
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
There should be a 6mFd and an 8 mFd cap on either side of the filter coil, one side of the field coil is connected to the same side of the 8mFd cap the filter coil is connected to. There is no electrolytic connected to the other side of the field coil.
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Agree, wire the replacement caps exactly as originals. Schematics sometimes have dots missing, which can get very confusing.
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Thanks guys.
Steve- checked shields and grid wire== all good.
Terry- will change .002 to .005.
Any thoughts on where to track down a 350,000 ohm vol. control? I have 250,000 and 500,000 ohm vol. controls in stock. Will either of these help?
Joe
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Either one should work fine.
Terry
Posts: 15,819
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
I believe we had the same case of missing dot here in this forum, from exact same cap, a couple of months ago.
There SHOULD be a tiedot between the wire from the right #50 8uF cap to #28 resistor, and the crossing wire from the top side of the field coil and left bottom pin of the output xfmr.
If you did not wire the cap after recapping back when it was, this can be the reason of your squealing, you have a positive feedback and ocillation using xfmr and the tone control caps as resonant tank, turning the output stage into an oscillator. Actually this is why I asked about this cap after your question about squealing. So I would check this before changing value of that 0.002uF cap.
If the cap is there, then it is something else.
(This post was last modified: 07-06-2012, 07:51 PM by morzh.)
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Dot was missing on schematic. You guys figured that out on the first 66 I did. That one was worked on in the past and left largely undone. The 2nd 66 was virtually untouched.
There is a connection at the point you question. Squeal is still there on left click on tone control. Hopefully will have some time this week to get back to it.
Thanks,
Joe
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
Finally had a chance to work on 66.
Replaced volume control and radio sounds great! The squeal on tone control also stopped.
Two birds with one stone.
Will take some photos and post.
Thanks to all again!!
Joe
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Joe, so glad you got another one working!
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 80
Threads: 10
Joined: Apr 2012
City: Waterford, NJ
A few photos of both 66s.
Thanks again for the great advice.
Joe
[Image: http://i1079.photobucket.com/albums/w511...lco66B.jpg]
[I[Image: http://i1079.photobucket.com/albums/w511...oth66s.jpg]MG]http://i1079.photobucket.com/albums/w511/jph141/66B3.jpg[/IMG]
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Two very nice sets!!!!
Terry
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 16B Parts
|
| Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM |
|
Philco 16B Parts
|
| Hi Dan,
Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM |
|
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
|
|
Hi Cap'n Clock,
Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM |
|
Philco 42-390, code 121 speaker
|
| Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM |
|
Philco 60 Squealing
|
| I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM |
|
Philco 6K7
|
| I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM |
|
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
|
| Hi Cap'n Clock,
Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A5...MrFixr55 — 06:48 AM |
|
American Bosch Model 802 auto radio
|
| I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM |
|
trying to identify this wire type
|
| Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM |
|
trying to identify this wire type
|
| It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM |
|
Who's Online
|
There are currently 6054 online users. [Complete List]
» 1 Member(s) | 6053 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
