Posts: 309
I saw a large Philco shouldered tombstone in a shop recently. It is a multiband radio with hexagonal knobs, 8 tubes and big honkin upright transformer on the left side as you are looking at the back. I could see no model ID on the chassis or on the bottom of the case. $60. If I remember correctly it had four bands. I probably should have grabbed it.
After looking for a week I can't determine exactly what I was looking at. Your thoughts please. Thanks.
OK, Now I understand why "eyewitnesses" don't always have the correct info when an accident or crime occurs.
The set is I believe a 97B, 7tubes, three bands and I already screwed it up.
I have damaged the dial. I have read about not cleaning these and I thought the lettering was on the back of the dial, not the front. I use Q-tips a lot to clean radios. I did the dial and got a lot of what I figure is tobacco smaoke off. It was fine and I should have left it, but did one more pass and took part of the lettering off. It is still usable but with one bad area. Have already checked and no repros for this dial. Color me stupid.
Here are some pics.
[Image:
http://i1185.photobucket.com/albums/z345...er/97b.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b1.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b8.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b6.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b9.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345.../97b10.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b5.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b3.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b4.jpg ]
[Image:
http://i1185.photobucket.com/albums/z345...r/97b2.jpg ]
Gene
(This post was last modified: 10-02-2012, 07:06 PM by
Gene Pederson .)
Posts: 292
Almost sounds like a 118B. Did it have a shadow meter?
Posts: 309
Hi Glenn,
Posts: 292
Look like this? This was my 118H, but it's the same chassis. This was pre-restore. I forgot to get a picture once it was cleaned up.
Attached Files
Image(s)
(This post was last modified: 10-01-2012, 11:25 AM by
Glenn Roberts .)
Posts: 309
I think that looks correct. Was $60 a good buy? How do these sets perform?
Posts: 292
They are great players! P/P. 42's., 3 gang tuner. I have a 118B in the stack. The problem seems to be when the shadow meter goes bad it stops playing unless a resistor is in place to keep the circuit active. I had 2 chassis and neither one had the resistor. Ron sent a picture to me to show the proper location.
(This post was last modified: 10-01-2012, 11:55 AM by
Glenn Roberts .)
Posts: 309
Thank You for all the info and help Glenn! I will check to see if it is still there.
Posts: 2,353
Hello Gene/Glenn: if it had four bands, eight tubes, and is in a shouldered cabinet it probably had an oval dial and is a model 650.
(This post was last modified: 10-01-2012, 12:10 PM by
TA Forbes .)
Posts: 309
Hi TA! And Glenn, I just called and it is still there so they are holding it for me to pick up tomorrow. And the price is $60. So whichever model it is should be good
The only pita I can see is there about 10 of the bakelite block caps in these, right?
Gene
(This post was last modified: 10-01-2012, 12:37 PM by
Gene Pederson .)
Posts: 292
Please post some pictures when you get it home
Glenn
Posts: 1,402
It would not be a 118 if it has four bands. It might possibly be a 640 or a 650, I'm not that familiar with the 6xx Philcos. At any rate, you better get back there and grab it before someone else does.
Posts: 1,402
Oops, I see TA already said that.
Posts: 309
Well Steve, and everyone I wasn't even close on the description.
See my edit and pics.
Gene
Posts: 1,402
Congratulations Gene, that was an excellent buy!
Posts: 2,353
Yes indeed, an excellent buy!!! The 97 is a three band , seven tube set, so you fooled us!
Users browsing this thread: 21 Guest(s)
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600.
NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one.
I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together.
As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog.
32-7528 choke is 65H, 10mA, 2,250 Ohm inductance.
Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM
Who's Online
There are currently 3878 online users. [Complete List ]» 3 Member(s) | 3875 Guest(s)
See my edit and pics.![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
