And, finally...a Scott Philharmonic!
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
A few weeks ago, I noticed someone had posted over at the E.H. Scott forum, wanting to sell an E.H. Scott FM Philharmonic in a Warrington cabinet.
The price was right, so I dipped into some savings and bought it.
[Image: http://www.philcoradio.com/images/phorum...786e6a.jpg]
It looked pretty nice to me, but when I saw the serial number, I knew I had to have it.
[Image: http://www.philcoradio.com/images/phorum...37b72a.jpg]
Notice the serial number starts with my initials (RR)?
I have never used a shipping service before, but since the set was in southeastern Kansas, I used Craters & Freighters for the first time. I have to say, they did a good job - the set arrived here undamaged.
[Image: http://www.philcoradio.com/images/phorum...b2fd77.jpg]
The set has no tweeters, and it is apparent that it never had any - there are no screw holes where they would have mounted. The woofer has a large "whizzer" cone.
All of the photos above were taken by the gentleman who was selling it for his neighbor.
I'll take some photos of my own and post here, after I clean this set up and reassemble it.
--
Ron Ramirez
Ferdinand IN
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
If that's the same firm tht sent my My Hammond amd Tone cabinet from Colorado Springs to New York, can't say enough positive about them. It's a niche market, and not cheap, but a few of them know what they are doing. Good of you to mention reliable movers.
Got to downsize soon myself, its time, so need good current moving references too. Please post specifics and contact information.
Posts: 594
Threads: 41
Joined: Aug 2010
City: Shepherdsville, KY
Joe Bratcher near Louisville, KY
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Posts: 717
Threads: 30
Joined: Feb 2008
City: Grand Rapids, MI
Sharp, Boss!!!
Mike
(This post was last modified: 10-12-2012, 11:00 PM by Michael Dennis.)
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Ron, what a great find. Looking forward to the receiver pictures as well. Love to see it after a little dusting. Don't know how you have the time for this stuff. Looks like the chrome should clean up well. If you don't like it, send it out here!
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 141
Threads: 13
Joined: Sep 2011
City: moline, il
Very nice find Mr Scott, 'er, I mean Ron.
I like the extra nice touch on the serial number plate lettering. meant to be.
Bruce
Posts: 3,138
Threads: 56
Joined: Apr 2011
City: Lexington, KY
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 309
Threads: 55
Joined: Oct 2011
City: Claremont, NH
What a beautiful set, Ron!!!
Congratulations
Gene
Posts: 337
Threads: 15
Joined: Nov 2005
City: Ortonville, MI
You're gonna like it. I had one years ago (chassis and speakers only), but the chromiumwas bad, and I wasn't up to stripping the chassis and re-donng them. I sold it.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
More photos.
First, the amp/power supply chassis after a good cleaning and polishing:
[Image: http://www.philcoradio.com/images/phorum..._00033.jpg]
Front view of the woofer, showing the whizzer cone:
[Image: http://www.philcoradio.com/images/phorum..._00035.jpg]
and a back view of the woofer:
[Image: http://www.philcoradio.com/images/phorum..._00034.jpg]
The entire set was quite dirty, with lots of mouse droppings. Even more trash was found at the bottom of the speaker pedestal... including the remains of a long-dead mouse.
Debbie and I cleaned the cabinet up, and I rubbed it down with Howard's Restore-A-Finish.
Now, a look in the back of the set, with the woofer and amp/power supply in place:
[Image: http://www.philcoradio.com/images/phorum..._00037.jpg]
The speaker mounting board has holes cut out for tweeters, but this set never had any - note the absence of screw holes:
[Image: http://www.philcoradio.com/images/phorum..._00038.jpg]
Now, a look at the back of the set with everything in place:
[Image: http://www.philcoradio.com/images/phorum..._00043.jpg]
I'll clean and polish the upper chassis later.
A close-up of the dial and knobs:
[Image: http://www.philcoradio.com/images/phorum..._00044.jpg]
And, finally, the reassembled Philharmonic as it now sits in our living room:
[Image: http://www.philcoradio.com/images/phorum..._00045.jpg]
--
Ron Ramirez
Ferdinand IN
Posts: 292
Threads: 17
Joined: Aug 2010
City: Yorkville IL
Happily back in Illinois..not.
Posts: 4,686
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Another unfortunate illustration of Scott's infamous flash chrome plating, if only they had triple plated it like the car manufacturers did back then. The cabinet on this set was perfectly fine, no lifting veneer, warpage, or other signs of moisture and water damage but the chrome plating still has rusted through and bubbled off in places.
For some reason most of the Philharmonics seem to be housed in Warrington cabinets, same with the Phantom series, it most have been the default cabinet option when these were sold. By the way, did anyone notice the pattern in the grille cloth?
Regards
Arran
(This post was last modified: 10-14-2012, 07:44 PM by Arran.)
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Well, Arran, in this case, the rust spots on the chrome weren't entirely Scott's fault. It doesn't help when mice have been hanging around your Philharmonic. And I think we all know what mouse urine can do to a chassis, especially one that wasn't chrome plated. In this case, I think the chrome plating saved the amp/power supply so that it still looks decent. I think if it had not been chrome plated, it would have already rusted through in places.
I am still amazed that none of the connecting cables were chewed, nor the speaker cone - even though I found the remains of a long-dead mouse inside the speaker pedestal.
--
Ron Ramirez
Ferdinand IN
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Philco 91 Speaker Replacement
|
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM |
Restoring Philco 37-604C
|
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one.
Which does not m...morzh — 01:44 PM |
Philco 38-2 Automatic Tuning
|
When you push the lever, you are supposed to rotate the disk to the desired station.
Then the magnetic tuning will acqu...morzh — 01:42 PM |
Philco 38-2 Automatic Tuning
|
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM |
Philco 91 Speaker Replacement
|
How would I go about removing the spider from the cone?dconant — 12:04 PM |
Philco 38-2 Automatic Tuning
|
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM |
Does anyone make photofinish replacements?
|
Here’s the link to the DIY photofinish section of our site:
klondike98 — 09:46 AM |
Delco car radio Peko vibrator converstion issues
|
Hi Richard,
Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM |
Delco car radio Peko vibrator converstion issues
|
hello mr Fixr,
The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM |
Delco car radio Peko vibrator converstion issues
|
How about putting a choke in the power supply?
The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM |
Who's Online
|
There are currently no members online. |
|
|