Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-15 finished
#1

Ok one last post to brag.

My 38-15 is finished. The dial face has a place where the dial needle rubbed the gold foil off. Other then that and it works great and I installed an input for an MP3 player.

Pics:
[Image: http://i1129.photobucket.com/albums/m501...99A47A.jpg]

[Image: http://i1129.photobucket.com/albums/m501...D26A0C.jpg]

What it looked like when I got it in Kutztown in May:

[Image: http://i1129.photobucket.com/albums/m501...99f9c2.jpg]

-Keith
#2

Keith, And well you should brag. That is a vey handsome radio. Great job.

Dave D
#3

All I can say is WOW!
#4

How does she play? Very nice, nifty bezel.

Paul

Tubetalk1
#5

Icon_thumbup Nice!!

Happily back in Illinois..not.
#6

She plays good pulls in AM and SW stations. The Bezel was pretty nasty so I used Brasso to clean it up. That made it to shinny so I coated it with a couple passes of medium walnut toner and then cleared it. I think it turned it pretty good.

-Keith
#7

Really nice job. Raising the bar for all!
#8

You did a really nice job! The grill cloth you used looks pretty good, too.

Tom
#9

That's a neat little set, Keith! Nice job!

What have you pulled in on shortwave?
#10

Nice job Keith, you are the "Wiz".
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#11

Very very nice!
#12

It looks good. There is a seller on Ebay who has many dial faces, and you may find one one of these days.

Web site: http://www.masekconsulting.net
Radio Photos: http://www.photobucket.com - album id FStephenMasek
#13

Shortwave mostly stations down in Mexico, I did pull in a couple from overseas they were speaking an Asian language. I don't do much SW listening.

Radio Daze sells a re-pop dial face for it but like a lot of their stuff there is no picture. Not sure how the re-pop would look I decided that the original one wasn't to bad. I have seen worse.

Thanks for all the comments everyone..

Should have the 610 console done this weekend. Finishing the cabinet for my AC Dayton, and will be starting restoration of a RCA Victor R-15 soon. I also need to finish up a 39-55 I shelved cause it was irritating me while trying to get the mystery control receiver to work.

It never ends...

-Keith




Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM

[-]
Who's Online
There are currently 7441 online users. [Complete List]
» 1 Member(s) | 7440 Guest(s)
Avatar

>