Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-190 bezel color question
#1

So I'm cleaning a lifetime of dirt off of the metal bezel with some green cleaner and while dirt is coming off, I'm left with areas that look like something ran down the bezel. So I try some alcohol and quickly realize that I'm removing the gold paint on the bezel. That's OK because I couldn't have put it on the radio looking like it did. So has anyone spray painted one of these bezels? I would describe it as a mat light gold color. Just go to Lowes and see what I can find?
#2

I found a thread answering this question.
#3

Although the paint recommended in that thread, Valspar Plasticote, was not available locally. So I picked up Valspar Brilliant Gold 66009 at Lowes. First coat was too thick and I got some noticeable orange peel. Quickly removed that with some alcohol and did 2 thin coats. I'm 100% satisfied.

With flash:
[Image: http://i191.photobucket.com/albums/z309/...file-8.jpg]

w/o flash:
[Image: http://i191.photobucket.com/albums/z309/...file-7.jpg]
#4

Hum. Mine isn't gold it is a nickle (plated?) color. I have had that radio for 30 years, so it is hard to remember, but I think it has always been that color.
#5

Quote:it is a nickle (plated?) color

Yes, it may be that color. Not plated, though, because alcohol takes it off easily. Like this?:

http://www.radioatticarchives.com/radio.htm?radio=2034

This one may be repainted; it's very close to mine now:

http://www.radioatticarchives.com/radio.htm?radio=2036
#6

When I stripped all the sexy gloss black off my escutcheon, I found traces of the original color underneath. I'd say yours is definitely in the right area. And funny you should mention, I think I bought the last can of the closest-thing-to on the west coast... I haven't seen it anywhere since.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently no members online.

>