Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 60 Antenna coil repair
#1

I have the last run (run 7) of the Model 60. The antenna coil is open where it goes from the 10k resistor to ground, it is listed as .7 ohms.

Does anyone know what direction and number of turns it needs to be? I haven't taken it out yet and would like the details so I can be ready to rewind it quickly.

Thanks,
Steve
#2

While you're waiting for an answer, you can still make the BC band work by jumpering that point to ground with a jumper if you want.
#3

Thanks, I will try that.

Steve
#4

I have the info, but it's bedtime for me here in the Eastern Time Zone. Icon_yawn I'll try to remember to look that up for you. Kindly remind me if I forget.

--
Ron Ramirez
Ferdinand IN
#5

Thanks Ron.
#6

OK Steve

Four turns of #38 gauge, clockwise (with the lugs of the coil facing you), starting at terminal 4 and ending at the ground lug (mounting bracket).

To find terminal 4, hold the coil up with the lugs facing you and with the mounting bracket at the bottom. Pretend the lugs are the face of an analog clock, and the mounting bracket is at the 6 o'clock position. The lug at roughly the 7:30 position is lug 1, and continue counting clockwise from there.

--
Ron Ramirez
Ferdinand IN
#7

Thank you Ron. I will try to get this done this weekend. The radio is playing well after the antenna so hopefully this will restore normal operation.

Steve
#8

What does this small coil do? The radio plays well on BC with the open end grounded. I am wondering if I really need to rewind it.
#9

It serves as the primary antenna winding for the "police" band (1.5 to 4 mc). There is a coil inside the antenna coil form which is the BC band primary. When the radio is switched to band 2 (police), this coil is shorted out, leaving only the 4-turn coil in the primary.

If you do not replace the 4-turn winding, when you switch to "police" band you will be shorting the antenna direct to ground and will then have no reception on band 2.

--
Ron Ramirez
Ferdinand IN
#10

Thanks. I thought it may be for the police band. Ill re-wind it now.
#11

I finished it this afternoon. It made a big difference in performance on the police band, especially at the 1500-1800kc range.

Thank you,
Steve




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
48-482 rear panel help
Hi Kettlechip and welcom to the Phorum. The back panel question is interesting. I have quite a few radios that use pow...MrFixr55 — 08:24 AM
Philco 46-480 Electronic Restoration
Not too much at all! :lol:  Sounds like you’re just dabbling into the hobby!jrblasde — 07:56 AM
Philco 46-480 Electronic Restoration
Hi Joseph, Fortunately, Ms. Fixr does not read my computer, or she would warn you against coming to me for sanity ch...MrFixr55 — 07:27 AM
48-482 rear panel help
There's a picture of one of the plastic covers in the following thread: I bought a full set of them in 2012 or so fro...klondike98 — 11:15 PM
Philco 46-480 Electronic Restoration
Good sanity check! You are correct—the first (as in, the most counterclockwise) position is for the push button presets....jrblasde — 11:05 PM
Philco 46-480 Electronic Restoration
Hi Joseph, First, verify that your band selector is in the correct position for what you want to do. I believe tha...MrFixr55 — 10:59 PM
Philco 46-480 Electronic Restoration
Got my replacement signal generator in the mail today! I was able to finish alignment of the IF section. I’ve got some t...jrblasde — 09:58 PM
The list of my radio & TV collection!
EdHolland. Glad you liked it. Thanks for the supportRadioSvit — 05:24 PM
The list of my radio & TV collection!
Great stuff, Peter thank you for posting.EdHolland — 04:06 PM
My Philco 37-116 Restore
The crack goes from almost the bottom of the tube to well past the fat part. It is an ST type tube. The filament is open...dconant — 10:04 AM

[-]
Who's Online
There are currently no members online.

>