Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 49-504
#1

When I got this little radio none of the components had been replaced. I replaced all the capacitors to include the electrolytics and bypass caps and quite a few resistors. The tubes seem to be fine but alignment was way out. I used a little Mother's Mag and Aluminum polish on the bakelite case and it looks much better than before although the photo doesn't show what it really looks like.

I also gave it an alignment and now I can scan from high to low on the dial and pull in about ten stations in the daytime. I'm rather happy with this one and it will be a keeper.

[Image: http://i180.photobucket.com/albums/x220/...F3841a.jpg]
#2

You have a very nice set. You should be able to pull in another 10 or so stations at night, or make an externall tuned loop, say 2'X2' (plenty of stuff on web) and probably get a carrier or signal from one axis or another on almost every channel. Great cure for insomnia.
#3

I never thought about a loop...good idea. I'd like to have one for my Atwater Kent Model 30 if I could find one that wasn't an arm and a leg like some I've ran across.
#4

Good little set. The brown ones polish nicely. The white ones can be a pain in the thing one sits on to clean up.
#5

I gave my sister a model 6D815 in white about 18 years ago. She recently passed away and I have it back again but it no longer plays so it's time to do some evaluating. I was fortunate in that there was little to do to it cosmetically. This is one just like it.

[Image: http://i180.photobucket.com/albums/x220/...815-W2.jpg]




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2821 online users. [Complete List]
» 1 Member(s) | 2820 Guest(s)
Avatar

>