Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 87 highboy owners
#1

Hi guys,I'm attempting to recreate the missing legs and base of a Model 87 Highboy-can some one measure the legs from the bottom of the leg to the bottom of the square top section of the leg?
Thanks!
Phil
#2

Your looking at 10 3/4".
Terry
#3

Thank You!
I would have thought it was much more!
Tallboy,you know!
Phil
#4

My 87 Lowboy is 10 3/4 ", the Highboy must be more.
Kent
#5

Thank God you posted that!
I was about to start cutting tomorrow!
Still looking for HIGHBOY owners.
Phil
#6

Phil

It will depend on whether you have a Highboy (doors that open out) or a Highboy De Luxe (doors that slide). (I see the photo you linked to is the Highboy.)

Highboy - http://www.philcoradio.com/gallery/1929b.htm#d
Highboy De Luxe - http://www.philcoradio.com/gallery/1929c.htm#g

I do not own either one, but if it will help -

Overall height of the Highboy - 47-1/8"
Overall height of the Highboy De Luxe - 50-1/8"

Measure your cabinet body and then cut your legs long enough to make up the difference.

--
Ron Ramirez
Ferdinand IN
#7

Sorry gents the 10 3/4 is for the lowboy!! Wasn't paying close attention and I always get confused on the high or lowboy cabinets. The 87 is one of my favorites!
Terry
#8

Thanks Ron,that will help.
Thanks for editing too,I read your earlier response I wasn't sure how to react to it.
Phil
#9

Sorry Phil, bad day yesterday. Good luck with that cabinet, eh!

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 3403 online users. [Complete List]
» 3 Member(s) | 3400 Guest(s)
AvatarAvatarAvatar

>