1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 201X - Name plate in radio???
cwysong
Junior Member
**
Posts: 26
Threads: 6
Joined: Jan 2011
City: Bothell, WA
#1

06-15-2013, 09:38 PM
I just finished stripping down a Philco 201X. It had lacquer on the inside as well as the outside. One thing I found when I cleaned the chassis board is an oval brass plate with the name of Powers on it. It is nailed in.
Did these radios get the name of the person who assembled the radio, or could this have been added after?
This radio has not been touched. The electronics are all original, and there was enough dust on it to make me think the insides have never been moved.
Has anyone seen this before?
Let me know.
Thanks
Chris

   
Find
Arran
Phorum Expert
*****
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#2

06-16-2013, 12:42 AM
Maybe the brass tag was put in there by a dealer? I have an RCA console where the dealer added their decal to the dial bezel.
Regards
Arran
Find
cwysong
Junior Member
**
Posts: 26
Threads: 6
Joined: Jan 2011
City: Bothell, WA
#3

06-16-2013, 07:00 PM
Aaron, I hadn't thought about that. I'll be the dealer put it on. For $250, this was a very expensive radio!
Thanks
Chris
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4074 online users. [Complete List]
» 2 Member(s) | 4072 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration