Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Restore a 37-610
#1

Hello all! I just wanted to firstly state that I am very new to radio restoration and want to say thank you in advance to any and all help that I receive. With that said, I have come into possession of a Philco 37-610 radio. At least that is what the the sticker on the inside of the cabinet claims. It appears to be a 37-623J cabinet, however. Anyways, I came into possession of this after my grandfather had passed. I would ultimately like to at least restore the cabinet for my grandmother as a gift. I believe that the electronic aspect may be a bit past me as it appears the components are in pretty poor shape.
Where could I find the knobs for this cabinet and a new grill cloth? Also, what's the best way to clean the dial (I know thats not the term, very new)? Again, thanks in advance and I am very excited to start learning about this new hobby!
#2

Are you near any of the meets? There is one this weekend in Huntington West Virginia where you cand find knobs and parts also those knobs are reproduced look on tubes and Moore.com and like sites. As for the dial there was a post on here that said mineral spirits will clean the dial without removing the numbers. Good luck finding grill cloth, reproductions have dried up.
#3

check out this site.I just found it myself! I hope it helps. http://web.archive.org/web/2005110310030...index.html
#4

Grillecloth.com (Radio Grille Cloth Headquarters) is out of business.

--
Ron Ramirez
Ferdinand IN
#5

A good place to start for finding knobs is the page on PhilcoRadio: http://www.philcoradio.com/resourceb.htm#l .
#6

Thanks for the advice guys! I think I will just plug away and try to find some knobs on the site Bob provided while periodically checking out eBay and Craigslist.
Is there anyway to find a list of where these meets are that Tab suggested I look into?
Also, I found this grill cloth on RadioDaze http://www.radiodaze.com/product/12906.aspx - is that the right one?
#7

Yes that's it I'm glad to see someone is selling at least some cloth. Todd




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, you refer to “AK”. Is that Alaska or Atwater-Kent, or… JoeJoe Rossi — 11:49 AM
Grundig 5088
Skip, you are back to this one? As for fixing, Mark Oppat fixes vol. controls. Don't know about Grunding, but woul...morzh — 10:30 AM

[-]
Who's Online
There are currently 2181 online users. [Complete List]
» 1 Member(s) | 2180 Guest(s)
Avatar

>