Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60L - Decal
#1

Hello,
I'm restoring a Philco 60 Lowboy, Canadian version.
The cabinet had already been stripped and I'm looking to reproduce the Philco decal. While I've seen that some are available commercially, from looking at other posting, there seems to be some question as to who gets them right. Since I already doing decals, I'd like to reproduce this one as well ( unless I can get a good commercial match.

So, would anyone know the correct size for this label or even, maybe a picture of an original. Ron posted some Philco label pictures on another post, I'm not sure if these would apply to my model.

Thanks for the help,
Daniel
#2

Hi Daniel

Here are a couple of the posts you mentioned.
http://philcoradio.com/phorum/showthread.php?tid=104
http://philcoradio.com/phorum/showthread.php?tid=529

The original decal used on your Model 60L was 1-1/2" long, and would have looked like this (image shown from a 645B tombstone, same decal):
[Image: http://i326.photobucket.com/albums/k420/...decal1.jpg]

Radio Daze offers the PH8 decal shown below, which is not exactly like the original.
[Image: http://i326.photobucket.com/albums/k420/...decal2.jpg]

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron for the info. BTW your article on the model 60 schematic variation is very well done and really get the confusion out. I really appreciate it.

I have one last question regarding the age of the radio. On your site I found reference to the 60L from January 1934, and on the evolution of the model 60 page, it indicates an introduction date as July 1933 but on my nameplate I find a patent date as 1930. So was this model produced in 1930 ?
Regards
Daniel
#4

No, the Model 60 had not even been thought of in 1930. The first Model 60 sets came out in July 1933, as shown on my website.

Patent numbers shown on those Philco patent labels can predate the actual manufacture of the radio by years; sometimes a patent could be several years older than the radio itself. For example, Edwin Howard Armstrong invented the superheterodyne circuit during World War I, but it did not come into general use until 1930.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2742 online users. [Complete List]
» 3 Member(s) | 2739 Guest(s)
AvatarAvatarAvatar

>