Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Identify this Aircastle
#1

   

I think it's an A31. Can anyone confirm this?

The artist formerly known as Puhpow! 8)
#2

Aircastle's are tough to identify. I had this one back in the mid - late 1980's, and never could find a model number on it. Or year of manufacture. My best guess was somewhere between 1933-1936. The cabinet on mine (and pardon the bad picture but it's all I have) is very similar to the one you have. In fact the only difference I see, based on the details I remember, is in the grille work, and that yours has a round dial where mine had a square one. I should've kept it, but sold it by the early 1990's, along with a 1937 Crosley, two Coronado's, and a 1950 Zenith console to make room for more Philco's Icon_e_biggrin

   

Greg V.
West Bend, WI
Member WARCI.org
#3

I'm in the same boat.. I've just got too many. I hate to sell this one, but I'm going to have to. It sure plays great. Like you said, no model number anywhere. Radio Museum brings up A31 when I input the tubes, but I can't find any photos of an A31 online to confirm it.

The artist formerly known as Puhpow! 8)
#4

Why not list the set you wish to sell in "For Sale or Trade" on this forum. I've got too many too, but there are a lot who don't feel they have enough.
#5

I might end up doing that. The wife mentioned something about putting it on Ebay, so I'll leave it up to her.

She thinks the idea of going to Kutztown is cool, so I'm being as cooperative as possible Icon_smile I'm sure I can find something at Kutztown to replace the Aircastle. Icon_smile Icon_smile

The artist formerly known as Puhpow! 8)
#6

I had an Air Castle similar to that a few years back, but forget the model number. I traded it off later when I had a slip of sanity. Wish I had it now.

No matter where you go, there you are.
#7

Yeah, go to Kutztown, travel in your smallest vehicle lest you be tempted............. Naw, bring the truck!
#8

Take the Aircastle to Kuntztown and either sell or trade it there for something else. Why help fleabay make another billion dollars, they don't do much to deserve it?
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4667 online users. [Complete List]
» 2 Member(s) | 4665 Guest(s)
AvatarAvatar

>