Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

49-1603 console
#1

Normally I don't go for postwar consoles, but this weekend I found a deal on a really nice 49-1603 that was too good to pass up. Plus, I think the cabinet is kind of interesting.

The chassis is just a 6-tube, so it shouldn't be any problem. I'm less sure of the phono. Were they putting multi-speed phonos in consoles in '49? Does anyone have a manual for this set or one that is similar?

Thanks,

Tom
#2

Tom I picked up a 49-1101, 9 tube model AM-FM model w/o rp they are not bad looking units but just not as sturdy as the pre-war models. They are smaller horizontal style consoles. Mine is in good condition and I plan on restoring it. I think they used a turntable a lot like the D-10's but were green in color.
#3

The 49-1603 uses the same radio chassis as the 49-1602. The 1603 has a model M-9C, combination changer instead of the M-9 of the 1602.

The M-9C has two arms; one for 78s and one for the new Columbia 33-1/3 LPs. There's a switch to select the arm of choice.

NOTE!! Different stylus tips! Do not use the 78 arm on an LP. All you'll do is carve out the groove and erase the record!

The 1602 and 1603 are "hot-chassis" sets. Use an isolation transformer!
#4

Thanks everyone for the info. The cabinet on this radio seems to be well built. Kind of surprising for a 1949 console with only a 6 tube AC/DC chassis and AM coverage. I haven't checked yet to see if the phono has both of its arms. Hopefully it does. That would make it the most interesting phono in my collection.

Chuck, does it say in the schematic which arm is which? You can probably tell by looking, but I just want to be sure.

Tom
#5

zenith82 Wrote:...

Chuck, does it say in the schematic which arm is which? You can probably tell by looking, but I just want to be sure.

Tom

The 78 arm on the left side is the automatic arm, linked to the changer trip mechanism, etc. It's the larger "klunky" rectangular arm. The 33-1/3 arm is the rounder, sleeker, smaller arm that is used for manual play and will not do auto-changes. It only shuts off moter at record's end.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2780 online users. [Complete List]
» 2 Member(s) | 2778 Guest(s)
AvatarAvatar

>