Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Picked Up Two Consoles Today
#1

This last Friday, I was bringing a Canadian Viking RM-370 back toa shop for this nice lady that works there. Because of continuing construction due to more flooding and road repair work I took a different route. Saw this antique shop and decided to check it out for a few minutes.

Walked in the door and lo and behold there are TWO consoles sitting in the place. A Philco 40-180 right by the door and a little further in is a set with a big honking curved glass dial! Looked it over and chatted with the owner for a bit and left. Got back home and started checking out the other radio. It is an RCA 813K which evidently are fairly hard to find.

Soooo.....I went back today to look again and the price tag on the RCA was $75. Asked what the best CASH price was today and he said $50---SOLD!
Then his partner says why don't you take the Philco too? You can have that for $25----OK!

So two new consoles and now to figure out where they will go. Some pics of the RCA. Needs some help on the case and the tenite bezel is broken as almost all of them are. Also on the very back is a bakelite piece that is broken and I will have to figure out if I can make it usable or try to find another.
[Image: http://i1185.photobucket.com/albums/z345...1e21e0.jpg]
[Image: http://i1185.photobucket.com/albums/z345...3b289e.jpg]
[Image: http://i1185.photobucket.com/albums/z345...2c41f2.jpg]
[Image: http://i1185.photobucket.com/albums/z345...35234e.jpg]
[Image: http://i1185.photobucket.com/albums/z345...554fce.jpg]
[Image: http://i1185.photobucket.com/albums/z345...304308.jpg]
[Image: http://i1185.photobucket.com/albums/z345...ef3d37.jpg]

Gene
#2

RCA, "all the way"! Does it also warn you that Will Robinson is "in trouble"?
#3

That 813k is a nice set.
I have an 816k that looks the same, but it has 16 tubes, and the cabinet is a little bigger.
You can heat a room with these sets. They throw off a lot of heat.
Great sound also.
I re-finished mine. It looks great and sounds great too after a full re-cap etc.
Good luck with it.
murf
#4

Great scores! Icon_thumbup

No matter where you go, there you are.
#5

I have to move to the "right" coast. Would never find such great buys here. Really nice score.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#6

Thanks for the kind words!

I don't know about Will Robinson, but I thought that was kind of neat to have the words in the station preset spots. Evidently the owner never put any station id's in the spots.

Gene
#7

That RCA is sweet, got some of that Jetson's design theme going.

Thanks,

Mike

Cossor 3468
GE 417A
Philco 118H
Radiola 17/100
Scott 800B6
Silvertone 6130
Stromberg 535M
Truetone D1952

#8

It looks like that broken Bakelite part is a switch made by Cutler-Hammer, I'm not sure how common or unique it is though. My guess is that it's purpose is to either kill the motor when the dial gets to the end of travel, or reverse direction. Fortunately the mechanism is very straightforward compared to an Airline (Wells Gardner) automatic tuning mechanism.
Regards
Arran
#9

Wow you will love the RCA-813. I have a RCA 816 and love it. Plays nice and strong.. Should not be too much difference to mine. And yours cost a whole lot less also.....Godd luck with it!
#10

Agree with everyone, the 813K is a pretty good set!!

Nice score!!Icon_thumbupIcon_clapIcon_wave




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM

[-]
Who's Online
There are currently 3595 online users. [Complete List]
» 3 Member(s) | 3592 Guest(s)
AvatarAvatarAvatar

>