Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

42-380 Art Deco
#1

Are there any statistics on how many of these were made and where they were marketed?
#2

http://www.philcoradio.com/gallery/1942a.htm#u

Where they were marketed? All across the USA. With 103,225 manufactured, it was Philco's top seller for the 1942 season.

--
Ron Ramirez
Ferdinand IN
#3

One of the prizes in my collection is my Philco 40-180, same Art Deco
cabinet except for the wood panel where the dial scale and knobs sit.
a beautiful surperb performer with an incredible richness of audio.
My other prize is a GE L 750a catalin which my Dad gave to my Mother
before leaving for service in WW II. One of the many GE products my father purchased at the GE Employees Store that was located in major
GE plants.
#4

I just picked up my first antique radio this weekend. It's the 42-380 and it was well worth the 13 hour round trip to Georgia to get it! It inspired me to do some inquiring about the history of Philco Corp, so I ordered this awesome book on Amazon. Then... I find this forum and low and behold, here's the author of that awesome book, Ron Ramirez! It's like I stumbled into the antique radio promised land!
#5

Welcome to the Phorum. Lots of great advice and help here!
#6

Thank you! I just signed on yesterday and have already gotten some priceless info that I will be utilizing on my new (old) Philco.
#7

PT57 - welcome and thanks, you're too kind. Enjoy the Phorum!

--
Ron Ramirez
Ferdinand IN
#8

Welcome PT57! I can say that, whether using this Phorum as an archive, or asking questions directly, it is a valuable resource. The group here is a great bunch, very helpful and informative. I highly recommend this YouTube series:

http://www.youtube.com/watch?v=IelT-Qp13po

It was recommended by a member here on the Phorum, I checked it out and found the recommendation to be great advice.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM

[-]
Who's Online
There are currently 2405 online users. [Complete List]
» 2 Member(s) | 2403 Guest(s)
AvatarAvatar

>