Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restoring a 39-7
#16

I prefer to keep rubber and wires separate. Icon_lol
#17

Thanks, I'll see if my local electronics shop has any...

Edit:

No luck. I have to go to the Internet. Any decent sources for these? I cannot locate any 6000pF caps, only 4700pF.

So what can I do? 4700 is enough, 10000 too much, or should I wire 3 2200's in parallel (I'd rather not tempt the fates of MTBF this way)?

Also there is one other silver mica capacitor in there - it's part 6A on the schematic. The problem is it's listed as a 20mfd device and there's no way this is 20mfd, it's just way too small. Elsewhere on the schematic it's listed as 20mmfd, which makes a lot more sense for this type of capacitor.
#18

It sings again!

After putting up with the repaired speaker that tended to muddle the sound and distort at medium-high volumes, I decided to take a closer look

The speaker was slowly disintegrating - small cracks were developing, and the most careful light touch caused the cone to split.

So I had the speaker reconed.

It's now a whole different radio. Plays loud, tight, and clear at all volumes.

I probably put more money I to this than I should, but it would have been a pity to leave it in such poor condition.

   
#19

Speaker looks very nice. Who did you send it to for reconing?
#20

The Speaker Shop:

http://thespeakershop.com
#21

Nice set! You've got the delux model with the brass escutcheon around the dial. Many years ago I had the chairside version of that set. Wish I hadn't sold it! Good player and very sensitive too.
Terry
#22

Actually, this one doesn't. It's pretty plain. I have a nearly identical model with the preset tuning buttons and the brass escutcheon though. You are right about the play quality and sensitivity though. A solid little radio. The guy who had it before me wrote 38-12 on the chassis, but it is a 39-6 as far as I can tell.

Edit: no, it isn't, it *is* a 38-12 chassis. Just double-checked the schematic. Someone put a dial from a 39-6 on it and stuck it in a 39-6 cabinet. >:-(

Aw crap! Just noticed I posted about the the speaker in my 39-7 thread. At least the 39-7 is a real one.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Hi Morzh, May be a good idea to remove the cone to prevent damage. You may have to do so anyway to remove the pole ...MrFixr55 — 08:44 PM
Philco 91 Restore Code ??
I think that Danaher, the company that owns Beckman-Coulter (the company that I worked for 41 years) owns Fluke. They a...MrFixr55 — 08:35 PM
Philco 91 Restore Code ??
Rod I wish... :lol: I am not sure I'd buy the Fluke, had it not fell in my lap for free. $500 to $800...it's a lot...morzh — 08:09 PM
Philco 91 Restore Code ??
Mike, ...you get a commission?RodB — 07:52 PM
New member
Hi. I specialize in refurbishing Predictas, but I'm in Chicago. If you can get it to me, I'd be happy to go over it. ...Bob Andersen — 06:43 PM
An attempt to remove the Field Coil from a G speaker
I have 3 G speaker, all with open Field coils. Today I pull one of the shelf and decided to try to remove the FC (spo...morzh — 06:07 PM
Philco 91 Restore Code ??
Thanks Mike. I will check them out.dconant — 05:52 PM
Philco 91 Restore Code ??
There is no such thing as bad Fluke. This said, they are expensive. A Fluke is easily 10x the price of comparable CCC...morzh — 05:45 PM
Philco 91 Restore Code ??
Hello Mike, Yes, I have 3 Fluke meters one being my first Fluke 77 and other being Fluke 87. My third is Fluke clamp -...radiorich — 05:04 PM
Philco 91 Restore Code ??
I knew that Fluke was the Cadillac so with that in mind what Fluke would you recommend I get?dconant — 03:53 PM

[-]
Who's Online
There are currently no members online.

>