Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

91X vs 15X
#1

I am a bit curious now that I have my 91X out and functioning again. I know that the 15X is an eleven tube set, but would the performance be any better than my 91X? Basically, would it be better enough to warrant me trying to track a 15X down? Since I am kinda stuck local until I figure an issue on my vehicle out, I figured I would do some research. Icon_smile

No matter where you go, there you are.
#2

I think that the 15X has separate mixer and oscillator tubes, an extra IF amplifier, and an extra audio amp, the 91X is pretty much like a Philco 90, the dual #47 version, but with 6.3 volt tubes, I think that the 15 would be a better performer, at least on distant stations, and more selective.
Regards
Arran
#3

+1, the 15 is a pretty good set!
#4

That being said I would not turn down either one if they were offered to me at a reasonable price, as yet I do not own a Philco console with an inclined speaker board.
I don't know if Canadian Philco offered models in those types of cabinets, I have seen highboy and lowboy models from then of course, and chairsides. I haven't seen a Canadian Philco with a fully skirted cabinet older then 1934-35, and it was a 16X. Philco of Canada used to contract out their cabinet construction to outside firms so they may not have offered the full range given the smaller market and different tastes.
Regards
Arran
#5

Hmm, sounds like it would be good to seek out a 15X then. With the way I tend to find uncommon Philco models in my region, that could be a realistic goal! Icon_thumbup

No matter where you go, there you are.
#6

Jay, I found one in Snow Hill, North Carolina. Although you CAN find good sets in the South, the hunting is definitely better in the North East.

Yes, you could definitely find one up there!
#7

I've had my 15X for many years and apart from replacing the filter caps it's never been worked on and it plays beautifully! One of my favorite Philcos. I aquired a 91X cabinet from an old collector a long time ago and want to make a complete radio with it. I found a restorable 91 chassis on Ebay for it recently. Still need to find the dual speakers for it though. hopefully one day I will be able to play them head to head and see which is the better setIcon_lol!
Kevin




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4460 online users. [Complete List]
» 5 Member(s) | 4455 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>