Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

This Was In My Xmas Card!
#16

Thanks to all for the valuable information. I have one more question. If I just want to clean the cabinet and not harm the existing finish, what product(s) are recommended these days. I figure if I give it a good cleaning, I can better ascertain just what needs to be done to the cabinet. Thanks, in advance, for your input.

Craig R.
#17

What a gorgeous radio! And what a great gift! The best cleaner is some Goop or GoJo (no pumice). Apply with a cloth, rub gently (always with the grain) and wipe clean. It might take more than one application to get it clean, depending on just how dirty it is. It will have a wet and shiny look for a few hours while it dries. Chances are a little Howard Restore-a-finish after that will bring it back to a near new appearance if the original finish is still largely intact. This is about as clean as I know how to make it.
#18

Craig, +1 on Eric's suggestion. That was all I did on mine other than the top. The top had a nasty water stain from presumably a plant watered on the top. I just couldn't get that to look like I wanted and the top is what one sees the most. That I took down and refinished.
You got a great deal on that radio! Mine was $190. The lady I bought it from has sellers remorse and has a standing offer of $400 to buy it back. With a pair of NOS 45s and other parts, it is about right, not counting labor. Not ready to sell it yet.
I did post on either the 111 or 112 on emptying out that big can and replacing the caps inside. I have not been able to find that thread yet and don't recall if the two chassis have different cans.
Shoot some pictures of your chassis and the can and maybe it will fire up some brain cells.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#19

Craig, I did find my 111 restoration thread finally! I hope this helps you. Pretty well documented.
Regards, Jerry

http://philcoradio.com/phorum/showthread...Philco+112

A friend in need is a pest!  Bill Slee ca 1970.
#20

Great resource, Jerry! I've got it bookmarked. Thanks to you and to everyone else for the very useful contributions. Couldn't do it without you! I've learned so much since joining the Phorum back in August. Should have done it sooner!

Craig R.
#21

Glad to help Craig. You might post your location a little closer than just California. I get out there now and then.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#22

You have a swell wife!

NOW give her a card with the same note in it!!

As I always say, "strike while the iron's hot!"

BUT..... perhaps that is why I have two ex-s..... Icon_wink
#23

That was a wonderful gift from your wife! And I am glad you found a set you really like. Doesn't get any better than this. EnjoyIcon_clap

Gene
#24

TA Forbes: I tried your suggestion but she picked an AIWA 6-transistor pocket radio from the 60's. That sort of backfired!

Gene: You are so very right! It doesn't get much better. She even helped me carry it upstairs! Got an email from the person who does my chassis work and he is suffering from boredom. So tomorrow I will be dropping off a couple of Philcos (1 of which is a Hippo) along with a Western Air Patrol for him to "tinker" with. What a guy! I wouldn't be involved in this hobby as much as I am if it wasn't for his expertise and guidance.


Craig R.
#25

Your buddy and your wife are part of what makes this hobby so great!

I say again: Cultivate the friendship of the old-time radio guys, be worthy of their company. Their knowledge is a treasure to be passed on.
#26

Me I think I would have printed out for sale ads for Zenith Stratosphere's

Maybe thats why I never got married...

John
Las Vegas, NV USA




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2973 online users. [Complete List]
» 2 Member(s) | 2971 Guest(s)
AvatarAvatar

>