Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco battery radios
#1

How hard are these to restore? I have my eyes on a 1937 model that has a 6 volt battery supply. Where can I find or how do I build a 6volt supply and a 1.5 volt, 90 volt supply. How good of a performer are these battery sets?
thanks
Chris
#2

The only battery-operated Philco sets I have ever restored were Model 38 sets. These were made from 1933 to 1936, have AM and the old "police" band. They play just fine, and the instant-on feature is pretty neat, too - you don't have to wait for it to warm up since the tubes are low current, directly heated filament type.

If the set you are looking at is a 6 volt set, it sounds like it was made to run (only) on a 6 volt battery. So you would only need a 6 volt DC source with a decent current capability. I'm sure it has a vibrator power supply, which introduces problems of its own if it uses a synchronous-type vibrator.

What is the model number of the set you are looking at? I would know more what to say about it if I knew exactly which set you were interested in...

Icon_smile

--
Ron Ramirez
Ferdinand IN
#3

I've done several battery radios, and the most difficult ones I've done were a couple of Zenith farm radios, a 5F134 and a 6V27. Leaned plenty from that pair! Had to build some fairly elaborate power supplies for those ones. I'll admit the 5F134 power supply was a bit of overkill (I used a 135V TV voltage regulator and a big transformer), and the 6V27 I'm still working on, with the intention of building a solid state vibrator replacement and run it off of a 6V power supply. A bit ambitious, you think? Icon_smile

Armed with the info I learned from the Zeniths, I've had a better time with the smaller farm radios I've done since, 2 Coronados and 2 Philcos, the latter being a 42-122 (covered in the "Latest Philco Save" thread), and a 40-95. Both are pretty simple circuits and not difficult to power.

I've got an AC supply I built that puts out 1.5V and 90V, but I've also built some battery packs that work great. A trip to Radio Shack will yield everything you need. A project box that will hold 10 9V batteries, battery clips wired in series, and a couple of D cell holders wired in parallel. I also use the 4 pin power connectors they sell for easy exchanging of the battery pack or the power supply.

If you like, at some point I can provide the schematic for the power supply if the group is interesed.

Bill

Sent from my Pentium II on the AT&T Dial Network
#4

The model number I am looking at is a 37-34 on ebay right now.
thanks
Chris
#5

For a 37-34 all you need is 6 volts DC @ 1.3 amps. And it does use a synchronous vibrator.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2841 online users. [Complete List]
» 1 Member(s) | 2840 Guest(s)
Avatar

>