Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Are 40-90 and 38-12TT the same radio?
#1

http://www.ebay.com/itm/Vintage-1938-Phi...51b7e8fb98


http://www.ebay.com/itm/1940-PHILCO-MODE...4acd828333

(short of the dial - in the 38-12 the dial is from Emerson, the org one was damaged).
#2

No, they are not the same internally (although the cabinet is the same).

38-12CB is AC operated; the 40-90CB requires batteries.

38-12CB: http://www.philcoradio.com/gallery/1938c.htm#c

40-90CB: http://www.philcoradio.com/gallery/1940a.htm#e

--
Ron Ramirez
Ferdinand IN
#3

Ron

I was surprised myself as I knew that 38-12 is more or less the same as 38-15 I have only with no shortwave band. And 38-14 is close to 38-15 but is AC/DC (hot chassis).

Does it mean that the guy who listed this radio (38-12) has 40-90 chassis in it?
they look the same, those two I listed.
#4

The cabinet is the same (style), so that doesn't necessarily mean the guy's 40-90 is in a 38-12CB cabinet (although it could be). When I have a little more time, I'll take a more careful look at the auction ad.

--
Ron Ramirez
Ferdinand IN
#5

OK, just looked at both auction links, Mike. Both are 40-90CB sets. The one identified as a "38-12 TT" is a 40-90CB, and it even comes with a Silvertone Powr Shiftr battery eliminator.

And, incidentally, both have their original Philco 40-90 dials (note the large "PHILCO" near the top of each dial).

--
Ron Ramirez
Ferdinand IN
#6

Thanks Ron,

This is the answer I thought I would hear now, as after you told me there were no 38-12 with batteries, and what triggered the question in the first place was the fact that I saw the chassis being identical.....

So, given the frequency of misnomers with Philcos recently I take it it is not that rare to buy something that is in fact might be something else. However close.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 3113 online users. [Complete List]
» 2 Member(s) | 3111 Guest(s)
AvatarAvatar

>