Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-675 for $50
#1

It appears that the prices for non-primo conditon radios has dropped quite a bit on ebay. I was the only bidder on a 37-675 that appears to be in good condtion but needs restoration. For $50 even the chassis is worth that much but to get a complete 675 for $50 is nice.
#2

Wow, what a steal! I didn't even see that one.

--
Ron Ramirez
Ferdinand IN
#3

I think I saw that one on eBay too. It was/is a De Luxe model, right? Congrats! 8)

Now why did this model originally cost so much more ($275) than the 37-116x ($195)? The 37-675x only has one central speaker, 12 tubes, and is not 'high fidelity' whereas the 37-116x had 4 speakers, 15 tubes, and IS high fidelity? I don't get it.
#4

http://cgi.ebay.com/370059057990 Not in mint condition but it is complete and shouldn't be that hard to restore.
#5

Claude, I almost bid on that. But the drive to get it, turned me off for right now. I was all set to hit that bid button, then I decided not to with about 30 seconds to go Icon_arrow Nice catch Icon_wink

-Brian
If you collect or are interested in antique telephones, please visit Classic Rotary Phones
http://www.classicrotaryphones.com/forum/index.php
#6

I guess as with many of the 37 models you could get this one with the shadow meter or without and this one is without (magnetic tuning). It really appears to be a lot like my 38-1 with PP 6F6's with a 6F6 driver so the output should be 12-15 watts. It has 2 IF stages so it should have decent performance, I have someone that is willing to wrap it up and toss it on a greyhound bus so that covers the shipping issue. For the price with shipping I might have ~100-120 into this radio so that isn't too bad. Actually it is probably a better performer than the 38-1, when I went back I noticed the 38-1 doesn't have a 2nd IF and rather than using a 6J5 as an inverter feeding a 6F6 driver to the PP 6F6 outputs the 38-1 using a 6J5 inverter feeding two 6J5 drivers to the PP 6F6 outputs sucking up one extra tube for the same result.
PhilcoBenz, more than likely the $275 was a typo and it should have been $175. Normally there was about $15-25 difference between the standard and Deluxe model in 37 so I think the price was more like $175. The one nice thing is that the Deluxe model was the less produced model of the two types with the standard being over triple the total of the Deluxe.
#7

You got a good deal on that set and you won't be disappointed in its performance. I restored a standard set a few years ago and was very impressed with it. I ended up selling it but it was tough to do. I have a 16X that I am going to keep and the two were a little too close electrically to justify keeping them both.

Sean
WØKPX




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 5375 online users. [Complete List]
» 1 Member(s) | 5374 Guest(s)
Avatar

>