Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Changed caps in a 40-190
#1

Soooo I finally got around to replacing the caps in my 40-190. Got orange dips from just radios.com. A lot of the stations sound great (850,1420,1100) and more. But on some I always get a low static even on some of the higher stations. Could it need a resistor replacement or just bad signal since I live on the ground floor in a condo?

AJ
#2

Easy to check for interference. Take it outside and try it. Plug it into a different circuit, etc. If that doesn't fix it, make sure the tuning cap is clean. Dust between the plates can cause static. Resistors? I always check them when I am recapping. If you didn't, you can be sure that at least some of them have drifted in 73 years. I don't know if that would cause static though...

The artist formerly known as Puhpow! 8)
#3

Disconnect the antenna loop and turn up the volume. If the static is still heard when no stations are being received, then most likely it is being internally generated.

If you only hear the interference when the antenna is connected then it probably is from an external source. As PuhPow mentioned try taking it outside as far from the house or other wiring as possible and see if it is reduced.

A bad resistor or cap can make static noises, but the noise will be present also with the antenna disconnected and no signal being received.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1367 online users. [Complete List]
» 1 Member(s) | 1366 Guest(s)
Avatar

>