Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A 20 dollar Craigslist find
#1

Up front, let me say that the pic is DEFINITELY an "after" one.

"Before" it had no speaker or dial glass, was filthy, and the chassis required me to rebuild the antenna coil, fabricate an RF choke, and un-do about a third of ALL the wiring due to some previous owner.

YES, I got it from one of the more,...uh..... "colorful" individuals I have met since I have been in the hobby. He was a tube collector who cataloged all his tubes by (drum roll): WHO he got the tubes from and the DATE he got them.

He wanted TOP DOLLAR for tubes BUT didn't care a whit about this set.

   
#2

Oh yeah, it's a Zenith 12S265.
#3

Tom,

Start sharing you luck.
Didn't they teach you in daycare - you gotta share!

Where's my X 12-tube set for...OK.....$60.
Where, I am asking you!
#4

I'll give you $70.
THat's a rare find for sure.
murf
#5

TA When did you purchase the set? Did you run away with the radio after you gave the guy the 20 dollar bill, because you stole that radio!
#6

Did he pull all the tubes out before he let you take it?

It's not how bad you mess up, it's how well you can recover.
#7

No tubes were in any radio he had. Go figure, right?
#8

Purchased several months ago. Took awhile to get 'er done.
#9

Nice find, and even nicer work on it! Just goes to show there are still deals to be found if one is patient.
#10

The Z was an extreme example of a "good deal." I am not a Z guy, but for the price..... who could turn it down!

But agree that the deals are still out there. The more folks that know you are a "radio-man," the more opportunities you will have presented to you.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2353 online users. [Complete List]
» 1 Member(s) | 2352 Guest(s)
Avatar

>