Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
I have 6AD6G indicator, which more often than not stays off, occasionally comes on, pretty dim in appearance, but when "on", operates normally and sensitive to the strong station.There is no loose connections.Shows 230 DC at the pin #5 (B+) instead of 180, but this 50v difference is across the board on all tubes- possibly from using 47 and 23uF caps instead of 40 and 20(?)
All other voltage readings are within norm.And I do not have the tube tester.
Time for the tube replacement? Thanks.
Posts: 15,832
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
http://www.ebay.com/itm/Pair-of-NOS-NIB-...3f32cd0d91
If no one bids, get them.
Meantime, is the a socket that has a resistor inside or something? Have you checked?
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
No, no resistors, just straight wire connections.
Posts: 15,832
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
If you are sure you have your filament current (can you see the filament glow when the tube is dark?) and your anodes (you do not have to have grid to have it glow) voltages and it is intermittent then it could be a bad tube with some intermittent separation inside.
Of course you have to exclude the possibility of bad socket connections etc.
Posts: 462
Threads: 40
Joined: Jun 2010
City: Lehighton
State, Province, Country: PA
Yeah, I think before I would do anything else I would run a pipe cleaner thru the socket holes and make sure they are clean, perhaps with a bit of DeOxit of it.
Larry
Posts: 214
Threads: 16
Joined: May 2010
City: Kokomo, IN
You might try resoldering the pins on the tube.
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
Done all of the above. I usually change all wiring, remove each pin socket, clean and tighten it. All pins have voltage, albeit 30% higher than normal.
I just found out that original 10watt 1,5K B+ resistor had been replaced with 1.0K resistor, hence the elevated B+ on all tubes, but that should not be detrimental to the glow issue.
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Fields, nice to post a link to the schematic. Every radio with an eye tube I have worked on (not your particular tube) has had a 1meg resistor either in the tube socket (mostly) or external and are a source of problems.
A friend in need is a pest! Bill Slee ca 1970.
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
@Jerry,
This one does not have any resistors.This particular set up is very interesting and unusual.Unfortunately, I am still having difficulties (or may be just ignorant) with a postings, but the schematic is on the NostalgiaAir and if you don't mind to see it there and let me know what you think, I would appreciate it. It is Airline 04WG803B. Thanks.
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Appears your right fields. Not familiar with that tube. Here is a link to the schematic for others.
Jerry
http://www.nostalgiaair.org/PagesByModel...011032.pdf
A friend in need is a pest! Bill Slee ca 1970.
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
Got the new tube, everything's fine, response to the tuning is OK. Thanks for the hint. Have a question on B+ voltage. The 1500 ohm 10W resistor at the rectifier had been replaced with a 1000 ohm. Could be on the account of the half dead E-caps.Now, after recapping, my B+ at the plates is 230v instead of 180v. How detrimental is it for the occasional usage of this set? Thanks.
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Tame the B+ to specs. No telling what excess voltage might do to your set. Use dropping resistor's) in voltage divider to achieve factory specs.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 60 Squealing
|
|
I just peaked it for the best signal at 600.
NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM |
|
Philco 60 Squealing
|
| Wavetrap no longer matters.morzh — 05:19 PM |
|
Philco 60 Squealing
|
| Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM |
|
37-690 Bass Choke Replacement
|
| Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM |
|
37-690 Bass Choke Replacement
|
| Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM |
|
37-690 Bass Choke Replacement
|
| Ah, now where to find one.
I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM |
|
Philco 38-7 Speaker
|
| Ask the admins to put them together.
As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM |
|
37-690 Bass Choke Replacement
|
|
This is the parts catalog.
32-7528 choke is 65H, 10mA, 2,250 Ohm inductance.
Find a suitable one.morzh — 02:18 PM |
|
37-690 Bass Choke Replacement
|
| While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM |
|
Philco 60 Squealing
|
| Your IF transformers are tuned to the resonant frequency they were designed for. When you observe the bell curve they di...RodB — 01:35 PM |
|
Who's Online
|
There are currently 3809 online users. [Complete List]
» 2 Member(s) | 3807 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
