Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Schematics needed
#1

I've checked with several sources suggested and cannot find the schematics for a Philco model 1775. Can anyone help?Icon_crazy
#2

I don't know what year that model is but you might want to try Chuck:
http://www.philcorepairbench.com/

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#3

From an earlier post, this radio would be too new for Chuck to have info on.
Not finding any info on a model 1775.

Carl
Northern Panhandle, WV
#4

Also, the full, correct model number will be 'XX'-1775, where the XX are the last two digits of the model year. Most likely, your set will be in the 50s or 60s. Like this: 54-1775, or 58-1775, etc….

This will help your search.

Chuck
#5

I suspect this is a Canadian Philco. Ask Chuck (Schwark) first, but I don't think he has any Canadian Philco schematics. If he does not have it, try Just Radios in Canada; they might have it.

http://www.justradios.com/schematics.html

--
Ron Ramirez
Ferdinand IN
#6

I have most of the Beitman yearly book from 1926 till they quit in 1969.
If you can give me a year it would help in trying to find it.
Is it just a radio or with phonograph
There may also be a letter in front of the model.
Guessing late 50s
no I deer if they have the Canadian models




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 2898 online users. [Complete List]
» 2 Member(s) | 2896 Guest(s)
AvatarAvatar

>