1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 40-190 Push Button Functions
NV3G
Member
***
Posts: 74
Threads: 42
Joined: May 2008
City: Shinnston, West Virginia State, Province, Country: USA
#1

05-18-2008, 06:36 PM
Philco 40-190 Radio Push Buttons

I do not have the cabinet, but just the chassis for the Philco 40-190 radio. There are 8 push buttons. I assume that some or all of them are presets for broadcast stations.

Are they all presets or do some of them serve another function other than being a preset?

Thank you.

Oscar -
NV3G
Find
TonyJSenior
Member
***
Posts: 111
Threads: 27
Joined: Oct 2007
City: Livonia, MI
#2

05-18-2008, 07:14 PM
According to a schematic I'm looking at, the buttons are as follows:

1-3 are presets, adjustable 540 to 1060 kHz
4-5 are presets, adjustable 650 to 1110 kHz
6-7 are presets, adjustable 920 to 1600 kHz
8 disables presets for manual tuning

Hope that helps!
Find
Guest
Unregistered
 
#3

08-11-2008, 10:13 AM
I am so glad I found this Philco radio forum. It is packed with much valuable information.

Is there a way to reset the push buttons on a model 40-180 to update them to a new favorite radio station?
Thank you in advance.

Phil D.
TonyJSenior
Member
***
Posts: 111
Threads: 27
Joined: Oct 2007
City: Livonia, MI
#4

08-11-2008, 10:37 AM
Sure can - there is a write up on how to do it here:

http://www.audiophool.cjb.net/Misc/philco_40-180.djvu

You'll need a DJVU viewer to open the document. Good luck!
Find
Guest
Unregistered
 
#5

08-11-2008, 11:32 AM
Thank you for the fast reply.
This is exactly the information that I was looking for.
PhilD.
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently 4003 online users. [Complete List]
» 5 Member(s) | 3998 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration