Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 59c Cabinet Restoration
#1

Here's a summary of the restoration done on a 59c cabinet.

As received:
[Image: https://www.dropbox.com/s/7wwjji0sb2p19n....jpg?raw=1]
and
[Image: https://www.dropbox.com/s/7cs2wsu3ttmyl7....jpg?raw=1]

Stripped:
[Image: https://www.dropbox.com/s/g6idavdzvh64vi....jpg?raw=1]

Toned and a couple lacquer coats:
[Image: https://www.dropbox.com/s/8i9zhcf9mqioan....jpg?raw=1]

Decal on...almost done:
[Image: https://www.dropbox.com/s/2bh5ehrc6pe4nz....jpg?raw=1]

Done and on the shelf (the grill cloth shows a bit too green in this particular light but in reality has a more golden tone to it...its from Kenneth Richmonds offerings):
[Image: https://www.dropbox.com/s/tj386dw99d9l78....jpg?raw=1]
#2

Shiny!

Icon_thumbup

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#3

Think that's good or bad?
#4

I think it looks great Bob, keep up the good work.

Gregb
#5

Don't get the big head <wink>, but Paul Sanders does what I consider one of the better refinishing jobs around and yours looks pretty close to his:

http://www.paulsandersclassicradios.com/...ntle-radio

Nice work on a neat little set!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

Good OR BAD?

I think my little thumbs up says it all, Icon_lol

I say, the shinier the better!

Ok well, not always, My bald spot is shiny and I don't like that but for radio finishes I like them original or like the day it was put on the store shelf.

A+ job

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#7

Thanks for the comments guys. I keep learning from each one of these I work on and a lot of that is from this Phorums comments and threads or conversations with Phorum members. Have to get back to the 39-25 that needs attention.
#8

wow I like it Icon_thumbup Icon_clap




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3966 online users. [Complete List]
» 1 Member(s) | 3965 Guest(s)
Avatar

>