1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Mikes 70 DONE
Steve Davis
Phorum Expert
*****
Posts: 1,400
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
#16

05-21-2014, 09:01 PM
Kirk, I think you are on the right track. A couple of coats of sanding sealer followed by the toner should do it.

Steve
M R Radios   C M Tubes
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#17

05-22-2014, 06:13 AM
Thanks Steve,
I went to buy it and boy has it gotten expensive. I took 4 years to use the last can so I think I will get my moneys worth.Icon_lol

Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#18

05-22-2014, 08:28 AM
Today I unclamped the base and it is nice and strong. If I dropped it off the 2nd floor it would survive. well, the base would...

I glued and clamped all the separations from the arch and the sides and tomorrow I will sand to remove any excess glue and grain fill the arch and molding on the front.


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
radiohenry
Senior Member
****
Posts: 496
Threads: 15
Joined: Mar 2013
City: Weymouth Ma
#19

05-23-2014, 03:19 PM
Kirk,
That is quite a job you are doing. I expect you will start getting inquiries regarding rrefinishing other radios.
Thanks for sharing,
Henry
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#20

05-24-2014, 06:09 PM
Unclamped the cabinet for the final time. I was going to grain fill but I found a veneer issue I didn't want to leave.


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#21

05-25-2014, 12:20 PM
GRAIN filler!!

Grain filler was finally applied to the cabinet! I stripped the molding and put sanding sealer on it. Will tone tomorrow.

All veneer is fixed, the entire cabinet is glued and solid. Faca and grill are completed.


Attached Files Image(s)
       
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#22

05-26-2014, 11:59 AM
Toning day,
Taped off the columns and toned the inside grooves Ex Dk Walnut.

Then toned the entire cabinet with a medium walnut. I want to let the lacquer set for a day so I can sand the cabinet before clear. Too much dander in the air and the finish is not smooth.


Attached Files Image(s)
       
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
morzh
Odobenus rosmarus
*****
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
#23

05-26-2014, 05:08 PM
Take your time Kirk, no rush Icon_smile
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#24

05-31-2014, 05:01 PM
Today was rebuilding day. I took the freshly toned molding and attached it back on to the cabinet with the original nails and added some glue. I filled any crevices and the countersunk nail holes and tomorrow I will finish toning the trim, Put the face back in and clear clear clear...

In about a week I will finish sand and wax her up.


Attached Files Image(s)
       
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
PhilcoJohn
Phorum Expert
*****
Posts: 1,455
Threads: 96
Joined: Jul 2012
City: Poughkeepsie, N.Y.
#25

06-03-2014, 07:03 AM
Can I say...........JUST BEAUTIFUL!!
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#26

06-03-2014, 08:33 AM
Bad start to a day!
Finished toning and Untaped to reveal pulled up finish and perfect brown seeped under the tape. Have to strip and re-start.


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
morzh
Odobenus rosmarus
*****
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
#27

06-03-2014, 08:48 AM
Bad Perfect Brown! Bad!
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#28

06-04-2014, 02:33 PM
Ok I finally got it right. Icon_crazy

I toned the front and then cleared 6 good coats. Sanded 400-2000 and will wait a day or so for the cabinet finish to harden. Then I will Apply some pumice and rub out the cabinet. Since it is a high gloss finish I will rub it out again with lemon oil and then wax her.


Attached Files Image(s)
       
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
morzh
Odobenus rosmarus
*****
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
#29

06-04-2014, 02:46 PM
And you people were serious when you told me that I could do all this!
I would probably retire by the time I finished it.
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#30

06-05-2014, 02:12 PM
Well I buffed her out with oil and cloth and then added 6 coats of wax.

I re-assembled her and now to let the wax harden for a week or so.

   
   
   
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM

[-]
Who's Online
There are currently 3619 online users. [Complete List]
» 4 Member(s) | 3615 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration