Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo
State, Province, Country: OH
Picked up this radio last Saturday at a lawn sale. Cabinet is in very good shape but the radio is missing the dial glass and the dial pointer is slightly bent and missing some paint. Any gotchas to look out for in this battery set? What is the correct battery voltages for this set? The Philco yearbook just gives the model number of the battery but no voltages.
[Image: http://i248.photobucket.com/albums/gg187...9ace99.jpg]
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
The battery voltages are 1.5 volts DC and probably 90 volts DC, if it uses tubes like a 1A7, 1N5, 1H5, 1C5, or the loctal versions like a ILN5. You can probably cross reference the battery model numbers someplace, although the schematic will likely have the voltage shown like on the screen and plate of the power output tube, or tubes. That being said these battery sets still suffer from the rotting rubber/gutta percha covered wire that most early 1940s Philcos suffer from, but it will not be as bad as an AC set usually, the battery cables will be the worst and should be looked at. You should let Ron add the picture to the gallery, I noticed that there is only a B&W photo from a book or sales brochure.
Regards
Arran
(This post was last modified: 06-25-2014, 02:47 AM by Arran.)
Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo
State, Province, Country: OH
Thanks for the reply Arran. Actually the battery cable and plug are not in that bad of shape but I'll most likely replace the wires anyway. Ron, if your reading this you most certainly can use the photo if you wish.
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Jim, if 90/1.5V there are some nice schematics for a small A/C supply that can be built and put in a faux battery enclosure. I have built a couple and there are threads on either here or ARF, one at least containing pictures of one I built. Try searching "farm radio battery". Here is a related link I have found but not the one where the schematic was posted (ARF?).
http://philcoradio.com/phorum/showthread...farm+radio
Best, Jerry
A friend in need is a pest! Bill Slee ca 1970.
(This post was last modified: 06-25-2014, 01:22 PM by jerryhawthorne.)
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Nice set, Jim!!!
A battery pack using 9V and 1.5V dry cells is easy to build. Just be careful when handling the 90V side, as this much DC can bite you!!!
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Jim - thank you!  It won't appear right away, but I will eventually get it posted. I really appreciate it!
And that is a really neat and unusual Philco battery set! 
--
Ron Ramirez
Ferdinand IN
Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo
State, Province, Country: OH
Finally decided to check out this radio and I am disappointed. The oscillator coil has an open secondary, antenna coil has an open secondary and the output transformer is open.
Not sure whether to try and resurrect this radio or bail on it. The speaker does check good but does have a repair to it so I don't know how good it will sound. Decisions, decisions.
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hi Jim
If you do want to get it going there are universal to replace the BC band coils. The output trans is going to be a little harder to come by because the plate resistance of the output tube are pretty high like 12K each. So youll need a 24K primary w/a ct. I would suspect that it would be a common problem as it's got to have a bunch very fine wire on the primary. Alot of the Philco 1939-42 portables use 67.5 v b batteries. Not that it matter a bunch.
Gud Lk
Terry
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
Jim
Give it a go
Terry is great at battery sets
Sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Grrrrr
Ur such a help!!!
Terry
ps his is going to be a bit of a job to fix. The original coils would be difficult to rewind, not like earlier sets. And then there is opt. Don't know if it is worth fixing.
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
terry
mr Philco said and i quote that is a really neat and unusual Philco battery set! [Image: http://philcoradio.com/phorum/images/smi...humbup.gif]
so that means it`s worth it
and they can`t put it on the Internet if it wasn`t true 
sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo
State, Province, Country: OH
Well good news is I went back thru the chassis and all the coils check OK, except for the OPT. Bad news is all the wiring needs to be replaced as its all crumbling rubber. Still not sure if I want to tackle this.
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
You should send it to Sam he loves replacing rubber wire!! Ha Ha
Terry
Some of those smaller chassis can be a real pita to work on. A friend
gave me a little PT-61 to get work and he told me that he had
recapped it. Thinking this would be a quick job I got it home had
a look at it What didn't tell me is that in doing so he had knocked
off about half of the rubber insulation. It's a kwel set but a pita none
the less.
http://philcoradio.com/gallery/1940b.htm#u
Gud Lk w/ your's
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
hey
i would take it
hmm first thing i would do is
terry
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
umm time to collect 8)
mafiamen2
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Well...I sent Jim a PM offering to buy if he decides not to pursue it. It is a really neat-looking set, unlike many of the Philco AM-only farm sets. This one has SW, a stylish cabinet, and pushbuttons.
--
Ron Ramirez
Ferdinand IN
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 60 Squealing
|
| Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM |
|
Philco 60 Squealing
|
| Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture.
dconant — 09:21 AM |
|
American Bosch Model 802 auto radio
|
| Hi Arran ,
Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM |
|
Philco 60 Squealing
|
| Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM |
|
Philco 60 Squealing
|
|
I just peaked it for the best signal at 600.
NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM |
|
Philco 60 Squealing
|
| Wavetrap no longer matters.morzh — 05:19 PM |
|
Philco 60 Squealing
|
| Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM |
|
37-690 Bass Choke Replacement
|
| Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM |
|
37-690 Bass Choke Replacement
|
| Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM |
|
37-690 Bass Choke Replacement
|
| Ah, now where to find one.
I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM |
|
Who's Online
|
There are currently 2309 online users. [Complete List]
» 2 Member(s) | 2307 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
