Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Cap Values on 15X & Riders Error
#1

http://www.nostalgiaair.org/PagesByModel...013138.pdf

The Riders manual is missing the cap values on the 15X. Not a big deal but it appears that at least 2 of the mica caps have become semiconductors - yes they leak in one direction only. Anyway they have an odd 2 dot value. They are part numbers 11 and 42 or 41. 11 tests at .01 but it would be nice to be sure.

Thanks

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#2

http://www.philcoradio.com/tech/images/15.jpg

(11) is 35 pF; (41) and (42) are both 110 pF.

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

Ron, you either have a library the size of the library of congress for all the Philco information, or the amazing ability to pluck this info off the top of your head! It's mind boggling, and very much appreciated. Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#5

My antenna was giving me a ground loop. Those caps are OK.

Riders says that the P-K voltage on the RF tube should be around 165 volts. I can see this in the 112 schematic since it has several resistors in the B+ but not on the 15. It is about 290V. Resistor 10 (160K) is right on as is cap 5 (.05uf).

The reason that I was looking at the RF amp is because cap 5 (the other half of a dual .05uf Bakelite block) is taking most of my signal to ground. Everything is fine with it out of the circuit, both in the local and distance settings.

??

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#6

I don't have the voltage chart near me right now, but the B+ at the RF plate should be at, or near, the same voltage as that on the plate of the 2nd IF tube with the local-distance in the "distance" position. The signal will drop with the switch in the "local" position since the RF tube's cathode is then connected to ground through (10), the 160K resistor. I would expect the RF plate voltage to be somewhat lower as well when measured between P-K in the "local" position as the Rider info calls for.

Could this be an effect of using a modern multimeter as opposed to the 1000 ohm/volt meters used in 1932?

Assuming both halves of (5) were replaced with new caps...the other (5) in the front end is an AVC filter cap.

--
Ron Ramirez
Ferdinand IN
#7

GarySP Wrote:Ron, you either have a library the size of the library of congress for all the Philco information, or the amazing ability to pluck this info off the top of your head!

Aw, Gary, you're too kind. It just comes from years of studying this stuff. I don't claim to know it all...

--
Ron Ramirez
Ferdinand IN
#8

Both of the caps are new and tested.

Yes there is some voltage difference with my new VOM but nor enough to account for the 165 - 290 volt difference. It is about the same as the 2nd IF.

There is about 30V to chassis ground in the local position and about 35V from K-Fil on the RF tube and about 15V on K-G.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3946 online users. [Complete List]
» 2 Member(s) | 3944 Guest(s)
AvatarAvatar

>