Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Fogged clear
#1

Here's a new problem that I've come across now that the weather is warm enough to spray. I'm using Mohawk Ultra Flo Clear Lacquer and obviously the humidity is too high because I'm getting some large fogged up spots.
Does anyone know what humidity is best for spraying clear? Right now at 9:15pm it's at 80%!
Thanks,

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#2

70% is about the absolute maximum. Some brands are a little more tolerant than others.

Steve

M R Radios   C M Tubes
#3

Eric, get some Mohawk No Blush Plus. Just a small spray will eliminate the fog. One can will last a loooonnnnggg time. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#4

Thanks, Ron. I just put an order in to AES for 2 cans. Icon_clap

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#5

So you apply it after you spray clear, or before, or when you get fog to eliminate it? How's it work?
#6

If you spray lacquer (whether it is toner or clear) and it comes out with a milky appearance, a quick spray of No Blush Plus will make the milkiness (blushing or fog) instantly disappear.

It doesn't take much, which is why one can will last a long time unless you are spraying lots of cabinets every day in high humidity.

And No Blush Plus is clear, so it can be used to correct blushing (fogging) on toner or clear.

--
Ron Ramirez
Ferdinand IN
#7

Which tells me that the milkiness then is purely surface phenomenon, the top surface forming into something not as smooth as it is supposed to be and the No Blush makes these wrinkles disappear. Otherwise it wouldn't help, were it structural and not surface.

Good to know.
#8

Steve Davis Wrote:Some brands are a little more tolerant than others.

Great point, Steve. Deft lacquer spray was very tolerant of high humidity.

Notice I said was, past tense. I went to Lowe's recently to stock up on Deft only to find that they no longer carry it. I went to the Deft website and it appears they no longer make it in spray cans. Icon_evil Icon_evil Icon_evil Icon_thumbdown

I really want to say something political...I really want to say something political... Icon_evil

But I think you can read between the lines here.

--
Ron Ramirez
Ferdinand IN
#9

Be careful Ron, I hear these new Super Moderators are pretty tough!Icon_wave

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#10

wow.. I usually use the ultraflo when it's more humid to avoid blushing. how humid was it? Mohawk recommends not to go above 65% or below 65 degrees. however, Bob Anderson did a video on one of his tombstones. seemed that around 55-60 the lacquer stayed fluid just a little longer and flowed out better.

that super blush retarder is wonderful stuff. just the lightest misting is needed. it disappears before your eyes like a TV commercial
#11

Quote:Notice I said was, past tense. I went to Lowe's recently to stock up on Deft only to find that they no longer carry it. I went to the Deft website and it appears they no longer make it in spray cans. Icon_evil Icon_evil Icon_evil Icon_thumbdown

Our local Lowe's no longer carries Deft at all. As a mater of fact, they no longer carry lacquer of any kind. Menards has Watco brand in quarts, gallons and spray cans. Their price is right too, a gallon is $24.99, which is the lowest I have found. We also have two Walmart stores close by. They both have Minwax lacquer in spray cans.

Steve

M R Radios   C M Tubes
#12

The Penguin is watching……

[Image: http://oi39.tinypic.com/mrs60w.jpg]
#13

I did a little research and it seems to be a decision by Penguin Paints who bought out Deft in 2013.
#14

We still have Deft at Home Depot and ACE, last time I checked. It is marked now as "brushing lacquer". I asked about that and the salesman indicated that due to VOC problems with reducing it with lacquer thinner they had to label it that way. It works fine reduced and sprayed. I don't use rattle cans and mix my lacquer with dye for toning.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#15

Jeez. I switched to Deft because it covers and finishes acceptably and the physical spray nozzle is superior.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently 1859 online users. [Complete List]
» 2 Member(s) | 1857 Guest(s)
AvatarAvatar

>