1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
48-482 push button coil winding specs ?
mikethedruid
Banned
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
#1

08-07-2014, 05:37 PM
Would anybody have the winding specs for the coils in the push button assembly for the 48-482 ? The gauge of the wire for each coil and the number of turns is what I mean. The coil for the lowest frequency button on mine is damaged, and, if I had the spec I could rewind it. If anybody has the information, I figure it would be useful to all us 48-482 owners to have a reference for all of them.
Find
morzh
Odobenus rosmarus
*****
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
#2

08-07-2014, 06:10 PM
Mike

can you count turns and measure the bobbin diameter?
The wire gauge is not that important as long as you can keep the average area of the winding the same which is simple if it is one layer coil.
(This post was last modified: 08-07-2014, 06:12 PM by morzh.)
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#3

08-07-2014, 08:03 PM
You might try a posting in the WTB, certainly someone has a parts chassis. Of course the simple approach is just one push button for tuning that does nothing. Not good I know!
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#4

08-08-2014, 11:07 AM
morah is right. Just count the turns and the direction of the wind and use some 36.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration