Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89/19 "before & after"
#1

        This 81 year-old cabinet turned out pretty nice. I used Mohawk toners and lacquer. The pretty wood grain on the front "came out" after I began toning. I wish it were mine but alas, I must return it to its owner next week.
Art
#2

Very nice job Art, the owner should be pleased.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#3

Well done!
Icon_clapIcon_clapIcon_clap
#4

Looks very nice.
#5

Icon_thumbupIcon_thumbupIcon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

Super job Icon_thumbupIcon_thumbupIcon_thumbup

Steve

M R Radios   C M Tubes
#7

Excellent work! Bravo!
#8

Super!
Love seeing restorations!
Before and afters are just awesome

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#9

Looks great, Art.Icon_thumbup I'm still learning the fine art of refinishing. Did you use grain filler on this one?

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#10

Eric,
No grain filler on this one. No sanding either. Just strip, tone, and finish.
Art
#11

Thanks Art. I've got a 66B that I'm about to start on. What would determine if I need grain filler or not?

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#12

Eric,
I would go by feel and looking at it with a magnifying glass. I don't fill if I don't have to. I think it's a lot of work that is not always necessary. Sometimes it depends on the type of veneer. Some wood is more open than others.

I mean it's an old radio and doesn't need a piano finish IMHO. But I know people feel differently about this.
Art
#13

Thanks Art. I agree with you.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#14

Really nice work !!
#15

Thanks all. It was nice to work on a cabinet that didn't require much repair. There was a very minor ding on the arch and a VERY minor area of missing veneer on the front curve that you can't even see in the picture and hard to see in person. Someone took good care of this radio. Too bad it was neglected the last several years. The chassis had layers of grungy dirt. The knobs are in excellent condition also and fit snugly on the shafts. I did not polish the escutcheon--just gave it a good cleaning. I hope the next one is as pleasant to redo as this one was.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2674 online users. [Complete List]
» 4 Member(s) | 2670 Guest(s)
AvatarAvatarAvatarAvatar

>