1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 53C to strip or not to strip?
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#1

08-25-2014, 12:13 PM
I have here a fine looking piece of Philco history but I cannot decide whether to strip it or leave it.

I gave it the Gojo but the top left finish is gone. front and sides are great though.

Do I leave it original and just seal the top or should it be redone?

I like original but the top is killing it. I cant just redo the top because it all curves together.

Here it is:


Attached Files Image(s)
               
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#2

08-25-2014, 01:48 PM
Most people would probably leave it as is. You could touch-up the top, but it would take some custom tinting of the lacquer. Several coats then a wet sanding of the entire cabinet followed by buffing it out.

It is easy to make it look worse attempting this, but it is a common approach for photo finish cabinets and could also be used here.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#3

08-25-2014, 02:47 PM
I'd leave it alone on front and sides.
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#4

08-25-2014, 02:55 PM
Kirk, if that is bare wood exposed on the top it appears to have a bit of color to it. I would put a small drop of lacquer on it and see what the color looks like. Perhaps they used clear lacquer on the top? If the color is close a touch up spray might help.
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#5

08-25-2014, 04:56 PM
I will try the lacquer first, then try to match it if that does not work.
If that does not work then I will just leave it for now. I like original and can always refinish it later

Thanks all,
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#6

08-25-2014, 06:34 PM
When I said , several coats, I meant on the area with the finish missing only. The tint would be to match the yellowing that has occurred to the original finish. BTW, yellow is not good, very little brown in gloss or semi gloss lacquer will do it.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#7

08-25-2014, 07:50 PM
Yes I got that,
We will see how bad I screw this up Icon_mrgreen

Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#8

08-26-2014, 01:01 AM
Here is one I fixed using that process.

   
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#9

08-26-2014, 11:23 AM
I matched the color and have added the first layer of new Lacquer


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#10

08-27-2014, 06:05 PM
I added a few more coats but was unhappy with the results. I added some toner to the area for a better match and it looks better.

Not happy with the dark color but I wll try sanding it a bit more and see what happens


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#11

08-27-2014, 07:25 PM
Come on Ron say it to Kirk Icon_twisted
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#12

08-27-2014, 07:46 PM
You are getting there. Now the trick is to not sand so much as to sand through the original finish. I would have used less toner.

Do you have a high speed buffer (not that Walmart orbital thing)?

Wait a few days before you try to buff it out.

It is going to look much better and still be close to original.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 08-27-2014, 07:47 PM by Phlogiston.)
Website Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#13

08-27-2014, 08:04 PM
Hay Kirk, you are getting there. A little sanding to get the darker area of toner down a bit. It still looks a lot better now than it did.
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#14

08-29-2014, 11:25 AM
Ok,
I have done the most I can without ruining the originality of the radio cabinet. I am not super excited about it but I like that it it still has that original look. We'll say that it gives it character. Icon_wink

Kirk


Attached Files Image(s)
       
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
klondike98
Phorum Moderator
******
Posts: 5,087
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#15

08-29-2014, 11:42 AM
Looks very good Kirk!!!
Icon_clapIcon_clapIcon_clap
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 9 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM

[-]
Who's Online
There are currently 6111 online users. [Complete List]
» 1 Member(s) | 6110 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration