Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New to the forum
#1

Hello.
I live in Spain and I am new to the forum.
I have several radios Valve, but so far no Philco.
I wanted to have a radio that can restore and I've decided on a 80 jr.
When I receive it I will put pictures, but you need an extensive restoration.
A greeting.
José
#2

Welcome to the Phorum! We are looking forward to seeing your pictures.

Steve

M R Radios   C M Tubes
#3

Welcome. Always like to here from new members. Lot of good & knowledgeable people here to help you if needed.
#4

Hola Jose,
Welcome!

You are sure to be an expert at restoring radios in no time flat with these guys to guide you.

I just got my first 80jr this week so it will be nice to see another one get restored!

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#5

Welcome to the Phorum!! There are several threads on this Phorum that are related to the 80Jr. If you are new to restoration here is another good place to start reading: http://antiqueradio.org/begin.htm
#6

Hello and Welcome! There are a lot of nice and helpful people on this forum to help you out with the workings of your radio. Hope to see pictures of your radio soon.
#7

Hola Jose,

Si decide que necesita ayuda, solo pregunta.
Suerte!
#8

Welcome, Jose!

I am looking forward to seeing your 80 jr.

It's not how bad you mess up, it's how well you can recover.
#9

I want to thank you for the great reception towards me.

When you receive the 80jr. I will provide photographs, sure I will need help and advice, I am now reading most forum threads to get familiar.

A greeting.
#10

The seller told me that the numbering is 326407.
What does that mean ?.

Somewhere law an article about it, but did not locate.
#11

Could be serial #, could be chassis #....no es muy importante.
What is important is that this is 80jr.
#12

Hola José,

Si necessitas de ayuda... ya sabes que puedes contar com ela.
Saludos
Carlos

Regards from Portugal,
Carlos
#13

Thank you very much Carlos.
Always so friendly.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 2558 online users. [Complete List]
» 3 Member(s) | 2555 Guest(s)
AvatarAvatarAvatar

>