1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
ok to strip?
TimC
☆
****
Posts: 262
Threads: 27
Joined: Jan 2010
City: Rochester, NY
#1

10-27-2014, 04:53 PM
Dumb question, but I'll ask anyhow

I have what I think is a 52 cathedral.
Some jackass thought the cabinet needed improvement..
Want to see if these were photophinish at all.
Too early a radio for photophinish I think.

Tim
(This post was last modified: 10-27-2014, 04:57 PM by TimC.)
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

10-27-2014, 05:10 PM
Nope, no photofinish on a 51B...
--
Ron Ramirez
Ferdinand IN
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#3

10-27-2014, 06:14 PM
Great news from Ron. That radio can be saved with a lot of stripping and refinish. Nice looking little cathedral.
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Arran
Phorum Expert
*****
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#4

10-27-2014, 09:38 PM
 One more thing though, use proper paint and varnish remover to strip the cabinet, lacquer thinner and acetone are not going to cut it this time. However the lacquer thinner and acetone are good from removing residue after you get the paint off. It looks like someone in the 1950s or 60s had a go at "Antiqueing" this poor model 52, that was the decorating trend of doubtful taste from that time, tackiness didn't begin in the 1970s you know.
Regards
Arran
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4462 online users. [Complete List]
» 2 Member(s) | 4460 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration